Bedienungsanleitung NAD M52 (Seite 6 von 10) (Englisch)

562260

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

REAR PANEL CONNECTIONS

4 USB

• Connect to USB 2 port of the M50 Digital Music Player using the

supplied USB A to USB B connector.

• Loaded CD in the M50 will be ripped automatically to the M52.

5 POWER

• Supply the AC mains power to the M52.

• When the POWER switch is set to ON position, the M52 goes to

standby mode as shown by the amber status condition of the

Standby LED. Press the front panel Standby button to switch ON the

M52 from standby mode.

• If you intend not to use the M52 for long periods of time (such as

when on vacation), switch o the POWER switch.

• With POWER switched o, the front panel Standby button cannot

activate the M52.

6 FUSE HOLDER

• Only NAD service personnel can access the fuse holder in the

unlikely event a fuse may need to be replaced. Refer all servicing to

authorized NAD service centers.

7 AC MAINS INPUT

• The M52 comes supplied with two separate AC power cords. Select

the AC power cord appropriate for your region.

• Before connecting the AC power cord’s plug to the mains power

source, ensure rst that the other end of the AC power cord is rmly

connected to M52’s AC Mains input socket.

• Always disconnect the AC power cord’s plug from the mains power

source rst, before disconnecting the other end of cable from the

M52’s AC Mains input socket.

FRONT PANEL CONTROLS

1 STANDBY BUTTON

• With the AC power cord’s plug connected to the mains power

source and the other end of the AC power cord rmly connected

to M52’s AC Mains input socket, switch ON the rear panel POWER

switch for the Standby button to activate. The Standby LED indicator

will turn from amber to blue.

• Pressing the STANDBY button again turns the unit back to standby

mode.

2 STANDBY LED

• This indicator will light up amber upon switching ON the rear panel

POWER switch.

• When the front panel Standby button is pressed to power up the

M52 from standby mode, this indicator will illuminate blue.

3 HARD DISC DRIVE (HDD) LED INDICATORS

• Display the status of the three hard disc drives (HDD). The HDD

LEDs will be in blue color if they are all healthy and active.

• If a disc drive fails, data will not be lost in this self-healing system.

Simply replace the drive and the system automatically recongures

itself.

• The color of HDD LEDs remains in red if M52 is not connected to

a M50. If the HDD LEDs remained in red after connection, it may

indicate that a disk drive(s) is missing; if ashing red, there maybe

disk drive failure. Refer all servicing to authorized NAD service

centers.

IDENTIFICATION OF CONTROLS

digital music vaultM52

hdd 1 hdd 2 hdd 3

1 2 3

USB

POWER

100-240V ~ 50/60Hz

4 5 6 7

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M52 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info