Bedienungsanleitung NAD PP3i (Seite 1 von 2) (Englisch)

602916

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

· Low noise, wide band MC/MM phono stage

· Connect your Turntable to most Ampliers, Receivers, and PCs

· Switched Line Level Input

· Highly accurate Analog-to-Digital Converter

· USB interface to PC for Vinyl-to-Hard Drive recording, USB cable

included

· Analog Line Level Output

· External 24V DC power supply

INSTALLATION AND OPERATION

CONNECT THE TURNTABLE TO THE PP 3i

1 Please make sure all ancillary equipment is turned o and that the NAD

PP 3i is not yet connected to its dedicated Power Supply.

2 Connect the leads from the turntable to the appropriate input sockets

on the back of the NAD PP 3i - MC for moving coil, MM for moving

magnet cartridge. Make sure you connect the Right channel to the

Right input; the Left channel to the Left input. Normally, red connector

denotes the Right Channel; white denotes the Left channel.

3 Once the turntable leads are connected, set the MC/MM switch on the

back of the NAD PP 3i to the correct input setting.

CONNECT THE PP 3i TO AN AMPLIFIER OR RECEIVER

1 Connect suitable RCA leads from the NAD PP 3i to the amplier or

receiver. Always use a so-called “Line-Level” input such as CD, AUX,

Tuner or Tape. Never connect the lead from the NAD PP 3i to an input

marked Phono or turntable.

2 Again, make sure to connect the red plug to the Right channel, and the

white plug to the Left channel of the amplier or receiver.

3 If the lead from your turntable is equipped with a separate earth (GND)

lead, connect this directly to a ground connection on the NAD PP 3i.

Use the thumb screw terminal “GND” which provides the grounding.

CONNECT THE POWER SUPPLY TO THE PP 3i

1 Connect the dedicated Plug-in Power Supply to the NAD PP 3i

(marked24V).

2 Insert the Plug-in Power Supply to a live mains socket; the blue LED on

the NAD PP 3i’s front panel will light up. Installation is now complete.

As the power consumption of the NAD PP 3i is negligible, it can always be

left switched on. It is recommended however that you disconnect the Plug-

in Power Supply from the mains if you are not going to use the NAD PP 3i

for a prolonged period of time (such as a holiday).

CONNECT THE PP 3i TO A PERSONAL COMPUTER

1 Connect the supplied USB cable (or any approved USB cable) between

the USB socket of the PP 3i and the USB socket of your PC. Your PC

should automatically recognize the PP 3i as a “new device” - the amber

LED of the PP 3i will illuminate conrming the connection.

2 Place the supplied “Vinyl Studio” CD in your PC’s disc drive and follow

the instructions to load the program into your PC.

3 Open the program and follow the instructions to get started recording

your LP’s to your PC’s Hard Disc Drive or other digital device.

DIGITAL PHONO / USB PREAMP PP 3i

User Guide

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD PP3i Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD PP3i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info