Bedienungsanleitung NAD T 754 (Seite 17 von 32) (Englisch)

606564

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

1717

ENGLISH

Adjusting the relative balance of your system's loudspeakers ensures that surround-sound recordings,

whether music or film, will present the balance of effects, music, and dialog that the artists intended.

Additionally, if your system incorporates a subwoofer it establishes a correct relationship between the

volume of the subwoofer and the other speakers, and thus of low-frequencies (bass) to other sonic

elements.

USING AN SPL METERUSING AN SPL METER

USING AN SPL METER

It is quite practical to perform the T 754 Level setup routines "by ear," and careful work will produce

acceptably accurate results. However, the use of an inexpensive sound-pressure level (SPL) meter, such as

Radio Shack part number 33-2050, makes this task easier, more accurate and more repeatable. Ownership

of such a meter could prove a valuable audio tool; your NAD audio specialist may be able to help you with

temporary use of a meter.

The SPL meter should be placed at the primary listening position, at approximately the height of the seated

listener's head. A tripod is helpful, but with a little duct tape almost anything — a pole lamp, music-stand,

or ladder-backed chair, for example — can do as well. Just be sure that no large acoustically reflective

surfaces obstruct or are near the microphone element. Orient the meter with its microphone (usually at one

end) pointing straight up toward the ceiling (not forward toward the speakers) and ensure that its "C"

weighting scale is selected. Set the meter to display 75 dB SPL. (On Radio Shack meters this necessitates

either setting the meter to its 80 dB range and taking your readings at the -5 point, or selecting the 70 dB

range and reading at the +5 point.)

SETTING CHANNEL BALANCESETTING CHANNEL BALANCE

SETTING CHANNEL BALANCE

Press the HTR 2 remote’s [Test] key, activating the T 754’s channel-balancing test signal and displaying the

<Channel Levels> menu on the OSD. You will hear a "surf" sound that cycles through your speakers,

beginning with the left-front. (If you do not hear the test signal, check your speaker connections (above),

and your <Speaker settings> OSD menu settings, (above.)

As the test signal cycles around the speakers, the OSD (and the VFL front panel display) will highlight the

currently playing channel. Now use the remote's [

/] keys to adjust the loudness of the noise output

from the currently playing channel to the required level (it’s usually simplest to begin with the left-front). The

"level offset" reading on the right will change by 1 dB increments; ±12 dB adjustment is available.

NOTE: If you are balancing levels "by ear", choose one speaker—usually the center—as a reference and

adjust each of the others in turn to "sound as loud" as the reference. Be sure that you remain in the primary

listening position while balancing all channels.

Using the remote's [

/] and [/] keys adjust each speaker to produce the same SPL meter reading

(or subjective loudness). Note that:

• All speakers must be in their final locations before level-setting.

• Your subwoofer (if any) should be set with its integral crossover defeated, or if undefeatable, set to its

highest-possible frequency if you are using the T 754's SUBWOOFER output. Final subwoofer-level

adjustment “by-ear,” using music and film sound material, is frequently useful.

• Due to the effects of room acoustics, matched-pair speakers (front; surround; back) will not always

calibrate to exactly the same level offset readings.

Your system's speaker distance settings are a subtle but important refinement of your setup. Informing the

T 754 of the loudspeaker-to-listener dimensions of each speaker automatically imposes the correct delays,

optimizing imaging, intelligibility, and surround-sound ambience. Enter your dimensions with precision within

about 1 foot (30 cm).

SETTING SPEAKER DISTSETTING SPEAKER DIST

SETTING SPEAKER DIST

ANCEANCE

ANCE

From the OSD’s main <Setup> menu, select the <Speaker Distance> item using the remote's [/] and

[Enter] keys. Using the [

/] keys, set <Front> and <Center:> to the distance measuring from your

principal listening position to the front surface of the front and center loudspeakers. Using the same remote

keys, set <Surround> to the distance of the nearest surround-channel speaker.

NOTE: Distance can be displayed as feet or meters selectable by the <DISTANCE> item in the Speaker

Distance menu.

The T 754 allows for setting of special listening and system options. These are usually one-time options

settings and once set do not need to be changed.

Main/Zone DSP Decoding

From the OSD’s main <Setup> menu, select the DSP decoding options. There are two options, 5.1 and 7.1

decoding. With 7.1 decoding, the Zone output will be switched off.

Dolby Digital Surround EX Decoding

Select either Auto or On. If On is selected, the Surround EX decoding will be forced on thus Dolby Digital

5.1 will become 6.1 matrix.

DTS-ES Matrix

Select either Auto or On. If On is selected, the ES Matrix will be forced on thus DTS 5.1 will become 6.1

matrix.

BACKGROUND to “ON” or “OFF”

When “ON” is selected, on-screen menus will appear against a black background, obscuring the current

video program (if any), when “OFF” is selected menus will appear in white text superimposed upon the

current video program (if any).

TEMP OSD

TEMP OSD. When “ON” is selected, the temporary OSD such as volume, and speaker levels are displayed.

When “OFF” no temporary OSD will be displayed.

ABOUT THE ON-SCREEN DISPLAYS (OSD) AND FRONT-PANEL READOUT

SPEAKER DISTANCE

ADVANCED OPTIONS

CHANNEL-BALANCE (TEST) SETUPCHANNEL-BALANCE (TEST) SETUP

CHANNEL-BALANCE (TEST) SETUP

NAD T 754 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 754

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info