Bedienungsanleitung NAD T 757 (Seite 18 von 44) (Englisch)

493495

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

DSP OPTIONS

LIP SYNC DELAY

DSP Options has the feature “Lip Sync Delay” whose function is to match

any delay that may occur in the picture relative to the audio.

By varying “Lip Sync Delay” from 0ms to 120ms, one can delay the audio

output in order to synchronize it with the video image.

TONE CONTROLS

The T 757 has two Tone Control levels – Treble and Bass. Bass and Treble

controls only aect the low bass and high treble leaving the critical

midrange frequencies free of coloration.

These controls allow one to tweak on-the-y, the frequency response

of the source during playback. The control setting could be adjusted by

navigating through the Tone Controls’ OSD menu via a combination of

[ENTER] and [ A/S/D/F ] keys.

Maximum and minimum values for all three Tone Control levels are ±10 dB.

“Tone Defeat” gives one the choice of varying or completely bypassing

the tone control section of the T 757. If “O” (“Tone Active” in the VFD) is

selected, the Tone Control circuits are active.

Select “On” (“Tone Defeat” in the VFD) to bypass the Tone Controls eectively

defeating the eect of the tone control circuits.

ZONE CONTROLS

Depending on the settings made at the separate “Zone Setup” menu

under the “Setup Menu” section discussion, Zone 2 can be congured and

managed via this “Zone Controls” window.

Select “On” to activate Zone 2. When activated, the Source input for Zone

2 can be allocated by selecting through the following inputs – All enabled

Sources, Front Input, Media Player, Tuner and Local.

As long as the associated Source input is active, it will continuously be

available at ZONE 2 output port in the rear panel regardless of the Main

Zone settings. For example, while the T 757 is at Source 1 mode, you can

set the Zone 2 Controls’ “Source” item to “Source 3”; the active Source 3’s

audio output will be directed to ZONE 2 output port in the rear panel even

though the T 757 is at Source 1 mode.

You can then feed the ZONE 2 jacks to another amplier or receiver

that maybe located in another area of your home or building. With your

separate amplier or receiver selecting the fed signal and with speakers

connected, you can then enjoy the zone selected source’s audio signal.

Select “Local” as your selected Zone 2 Source input if you wish to enjoy the

same source as the main Zone and allow simultaneous listening, but with

full separate volume levels.

If a Zone 2 is set to “O”, it is deactivated or powered o.

IMPORTANT NOTICE

Only analog audio connected through a Source’s analog audio input

port can be associated as audio source for Zone 2. Digital audio sources

connected via HDMI, digital optical and digital coaxial input ports

cannot be downmixed and used as Zone 2 audio source. Ensure also

that the associated Source’s Digital Audio setting is set to “O” or no

actual digital source is connected.

VOLUME

“Volume” refers to the adjustable secondary Zone 2 Volume level that can

be increased or decreased depending upon its settings. This is applicable

only if the Zone 2 Volume setting in the separate “Zone Setup” menu under

“Setup Menu” is set to “Variable”. If set to “Fixed”, this “Volume” item at the

Zone Controls section will not be available.

NOTES

• IfZone2isstillONandSTANDBYbuttonispressedtoswitchtheT757

to standby mode, the VFD will be extinguished but the STANDBY LED

remains illuminated blue. This indicates that Zone 2 is still active. In

order to completely shut down the T 757 together with Zone 2, press and

hold STANDBY button until the STANDBY LED turns amber.

• Zone2isaudioonlyandnotassociatedwithanyvideoinputsources.

OPERATION

USING THE T 757  MAIN MENU

ENGLISH PORTUGUÊSFRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 757 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 757

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info