Bedienungsanleitung NAD T 758 (Seite 29 von 42) (Englisch)

745046

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

DTSES MATRIX 6.1

In this format, the additional signals of the back channel receive a matrix

encoding and are inputted into the right and left surround channels.

During reproduction they are decoded to the right, left and back surround

channels.

Since this bit-stream format is 100% compatible with conventional DTS

signals, the DTS-ES Matrix 6.1 format eect can also be achieved from

sources with DTS-ES 5.1 signals.

Naturally, it is also possible to reproduce from a DTS 5.1 channel decoder,

signals recorded in DTS-ES 6.1.

When a DTS-ES decoder processes a discrete DTS-ES 6.1 or in Matrix 6.1,

these formats are automatically detected and the Optimum Surround

mode is selected. However, some DTS-ES Matrix 6.1 sources may be

detected as DTS. In this case the DTS-ES Matrix mode should be selected

manually in order to reproduce them.

DTS NEO: 6 SURROUND

This mode applies the conventional 2-channel signals such as digital PCM

or analog stereo signals to the high precision digital matrix decoder used

for DTS-ES Matrix 6.1 to achieve 6.1-channel surround playback. DTS Neo: 6

surround includes two modes for selecting the optimum decoding of the

signal sources:

DTS NEO: 6 CINEMA: This method is ideal for the reproduction of

movies. The decoding takes place by emphasizing the separation

in order to achieve the same atmosphere with 2-channel, as with

6.1-channel sources.

DTS NEO: 6 MUSIC: Mainly recommended for music reproduction. The

right and left front channels do not pass through the decoder and are

reproduced directly so there is no loss in sound quality, and the eects

of the right surround, left surround, central and back surround channels

add a natural sensation of expansion of the sound eld.

ENHANCED STEREO

Please refer to the same description of ENHANCED STEREO under the LISTENING

MODES segment of the OPERATION - USING THE T 758 - MAIN MENU.

DISPLAY SETUP

The Vacuum Fluorescent Display (VFD) and On-Screen Display (OSD) can be

shown in various ways by navigating through the parameters at the Display

Setup menu. Use a combination of [ A/S ] or [ENTER] and [ D/F ] keys to

step through the Display Setup menu items.

NOTE

The congurations set forth at “Display Setup” are carried over whenever

it is enabled during A/V Presets setting. Please see also the section below

about “AV Presets”.

VACUUM FLUORESCENT DISPLAY VFD

Display: Select “On” to display all applicable data or characters at the

VFD. Nothing will be shown at VFD if “Temp” is selected. At “Temp” setting

however, whenever any of the front panel controls or their corresponding

keys in the remote control is activated, the appropriate VFD characters will

be shown temporarily and then fade away.

Dimmer: If it is desired to reduce the brightness of the VFD, set Dimmer to

“Dim”. Otherwise, select “Bright” to return to normal VFD brightness.

Line 1, Line 2: The VFD shows two main lines of data or characters. Line

2 is the line of data or characters located at the lower bottom of the VFD

while directly above it is Line 1. For both lines, one can select which display

could be shown by choosing through the following

Main Source: Shows the active Source.

Volume: Current Volume level is shown.

Listening Mode: Selected Listening Mode is shown.

Audio Src Format: Shows the active Source’s detected audio format.

Audio Codec: Displays the detected audio stream format like Analog,

PCM Surround, Dolby TrueHD, DTS-HD Master Audio and other formats.

Video Mode: Show the video resolution of the active input source.

Details shown include the video resolution with frame rate. For a better

understanding of these video details, consult with your NAD Audio

Specialist or your distributor’s technical department.

Zone 2 Source: The assigned Source for Zone 2 is shown.

O: Select “O” if it is desired not to show any data at the applicable Line.

Temp Line: Choose between Line 1 and Line 2 as the desired line where

VFD will be temporarily shown if “Temp” is selected at “Display” option as

described above.

ONSCREEN DISPLAY OSD

Temp Disp: This applies to the OSD that is temporarily shown at video out

whenever any of the front panel controls or their corresponding keys in the

remote control is activated. Set to “On” if it is desired to show the applicable

OSD at the monitor/TV; otherwise, select “O”.

OPERATION

USING THE T 758  SETUP MENU

ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 758 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 758

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info