Bedienungsanleitung NAD T 758 (Seite 33 von 42) (Englisch)

745046

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

The T 758’s internal AM/FM tuner oers very high quality sound from radio

broadcasts. The reception and sound quality will always be dependent to a

degree however on the type of antenna(s) used as well as proximity to the

broadcast origin, geography and weather conditions.

ABOUT ANTENNAS

The supplied FM antenna can be connected to the rear panel FM antenna

input using the included “balun” adapter and should be fully extended

to form a “T”. This folded-dipole antenna will usually work best when

oriented vertically, with the arms of its “T” fully outstretched and arranged

perpendicular to the origin of the desired broadcast. There are no

“rules” however, and experimenting freely with antenna placement and

orientation may yield the clearest sound and lowest background noise.

In areas of poor FM reception, an exterior FM antenna can improve

performance dramatically. If radio listening is important to you, consider

consulting an antenna installation professional to optimize your system.

The supplied AM “loop” antenna will usually provide adequate reception.

However, an exterior AM antenna can be used to improve reception.

Consult an antenna professional for more information.

IMPORTANT NOTE

When using the AVR 4 to carry out AM/FM commands, ensure that the

DEVICE SELECTOR is set to “TUN”.

ASSEMBLING THE LOOP ANTENNA

1 Rotate the outer frame of the antenna.

2 Insert the bottom edge of the outer frame into the groove on the stand.

3 Extend the antenna cord.

SELECTING A TUNER BAND

Press the [AM/FM/DB] button on the AVR 4 while at AMP or TUNER device

selector page. Each subsequent press will toggle you through AM, FM or

DAB band. Stop (release button) at your desired tuner band.

TUNING AM/FM STATIONS

Upon selecting AM or FM band, use SCAN [ 5/6 ] on the AVR 4 to perform

slow manual search; press and hold to automatically search.

The front panel [ a/s ] or AVR 4’s [ A/S ] buttons can also be used to tune

for stations.

1 Press [ A/S ] momentarily to step up or down between AM or FM

frequencies.

2 Press and hold [ A/S ] for more than 2 seconds to search up or down - the

T 758’s tuner will stop at the next suciently strong signal it encounters.

3 Pressing the [ A/S ] during the search process will stop the search.

DIRECT TUNING

If you know your desired station’s frequency allocation, you can tune

directly to the station.

1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see

the lower line of the VFD). Select “Tune” mode.

2 Using the numeric keys of the remote control, key-in the frequency

allocation of the station. For example, to enter 104.50MHz, press “1”, “0”,

“4”, “5” and “0”.

STORING PRESETS (AM/FM/DAB)

The T 758 can store a mix of your 40 favorite AM, FM and DAB radio stations

for immediate recall.

1 To store a desired AM/FM station to a preset, rst tune to the desired

frequency (see above), then press AVR 4’s [MEMORY] button. The VFD

will show the next available Preset number - for example, “Preset 4 Free”

in the lower line.

2 Press the [MEMORY] button again to store the desired frequency on

the Preset number shown (“P04” is shown in the upper right corner of

the VFD). Your desired frequency is now stored in the assigned preset

number.

NOTE

If there is no more vacant Preset number, you can overwrite an existing

Preset number by pressing the [ D/F ] buttons to select the Preset

number you want to overwrite.

DIRECT RECALL OF A PRESET NUMBER AM/FM/DAB

You can directly recall a desired Preset number.

1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see

the lower line of the VFD). Select “Preset” mode.

2 Using the numeric keys of the remote control, directly key-in your

desired Preset number. For example, to enter Preset 5, press “5”.

DELETING A STORED PRESET AM/FM/DAB

You can empty a preset by deleting the stored information.

1 Select the preset number to be deleted. For example, “P03”.

2 Press and hold [DELETE] button until the current Preset number shown

in the VFD is extinguished (“P03” becomes “P--”.).

CHOOSING THE TUNER MODE

The AVR 4’s [TUNER MODE] key is a dual-purpose control. Toggle [TUNER

MODE] to switch between “FM Mute On” and “FM Mute O”. In the normal

position, “FM Mute On”, only the stations with a strong signal can be

listened to, and the noise between stations is muted.

Pressing the [TUNER MODE] button again (“FM Mute O”) allows distant

and potentially noisy stations to be received. Noise is reduced if the FM

station signal level is less than the FM Stereo threshold (since mono FM is

inherently less noise-prone) though at the sacrice of the stereo eect.

NOTE

One can store the same channel in two preset locations - one with “FM

Mute On” and another with “FM Mute O”.

OPERATION

LISTENING TO AM/FM RADIO

ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 758 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 758

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info