Bedienungsanleitung NAD T 775 (Seite 24 von 46) (Englisch)

602917

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

MUTING THE SOUND

Use the HTR 3’s ‘Mute’ key to silence all channels completely. Muting is

always available regardless of the source or listening mode selections.

NOTES

• Changinginputorlistening-modeselectionsdoesnotreleasemuting.

• AdjustingthevolumelevelviatheHTR3orthefrontpanelvolumeknob

willautomaticallyreleasethemutefunction.

ADjUSTING CHANNEL LEVELS ‘ON THE FLY’

You can make changes to the relative levels of center, surround and

subwoofer outputs without having to go into the ‘Speaker Levels’ menu.

This is very convenient in circumstances like increasing (or tone down)

a lm’s dialog level by raising (lowering) the center channel or reducing

excessive deep bass (or enhance deep bass) by lowering (raising) the

subwoofer level.

Use the HTR 3’s ’SURR,’ ‘CENT’ and ‘SUB’ keys for direct-access level

adjustment of these channels over a range of ±6 dB.

The surround back channels (if any) adjust in lockstep with the surround

channels.

NOTE

 Levelsettingsadjusted‘OntheFly’areaddedorsubtractedtothesetup

levelsestablishedattheT775level-calibrationroutineasinvokedby

theHTR3‘Test’key.However,selectinganyPresetwillrevertthechannel

levelstothosestoredinthepreset.ItwillalsotakeT775othelevelsset

viaAudysseyAutoCalibration.

ZONE SETUP

The Zone feature allows one to simultaneously experience in dierent

zones of the house multiple sound and applicable video sources from all

enabled Sources as well as from Front Input, Media Player and Tuner.

The T 775 has three congurable Zones – Zone 2, Zone 3 and Zone 4. Use

a combination of or ENTER and keys to navigate through the Zone

Setup menu parameters.

VOLUME

Zone 2 have Fixed and Variable volume control. When set to ‘Variable’

and while at the ‘Zone Controls’ menu OSD, the Zone 2 Volume level can

be adjusted using the HTR 3’s or the corresponding front panel

navigation buttons or directly via ZR 4’s VOL .

On the other hand, if Volume is set to ‘Fixed,’ the Zone 2 Volume is set to

a preset dB level and thereafter the Zone’s volume can be varied via the

volume control of the separate amplier it is fed into.

MODE

Zone 3 and Zone 4 can be congured into two modes – Record Out and

Zone (Audio Only). If the selected mode is Record Out, the audio and

applicable video signal of the assigned Source are directly sent out to the

applicable Audio/Video Output (See Item 5. AUDIO 3 OUT/VIDEO 3 OUT/S-

VIDEO 3 OUT, AUDIO 4 OUT/VIDEO 4 OUT/SVIDEO 4 OUT of REAR PANEL

discussion.) When Zone 3 or Zone 4 is set to ‘Record Out’ mode, they will not

be available at the ‘Zone Controls’ section of the Main Menu window.

‘Record Out’ setting is ideal for making recordings with a VCR or other

similar devices. This setting is also used for multi-zone installations using

passive ‘impedance matching’ volume controls. See your NAD dealer for

specic information about integrating your NAD Receiver into a multi-room

audio distribution system.

Zone 2 and Zone 3 ‘Volume’ will function the same way as that of Zone 2

when ‘Mode’ is set to ‘Zone (Audio Only).’

See discussion also on ‘Zone Controls’ at the Main Menu.

NOTE

 TheZR4remotecontrolwillonlycontrolZone2applications.

AMPLIFIER SETUP

If the surround back speakers are not used in the main zone, their surround

back amplier channels could be assigned for Main back, Main Front (Bi-

Amp) and multi-zone use.

The Surround Back amplier is congurable through the following settings

• MainBack: Assign as surround back speakers.

• MainFront(Bi-Amp): Provide a bi-amp mode for the Main Front

speakers (Left and Right) speakers thus reproducing the Front Left and

Front Right amplier channel outputs.

• Zone2: Assign the surround back amplier channels to supply Zone 2

speaker level outputs from the surround back speaker terminals.

• Zone3: Assign the surround back amplier channels to supply Zone 3

speaker level outputs from the surround back speaker terminals.

• Zone4: Assign the surround back amplier channels to supply Zone 4

speaker level outputs from the surround back speaker terminals.

OPERATION

USING THE T 775  SETUP MENU

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 775 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 775

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info