Bedienungsanleitung NAD T 775 (Seite 43 von 46) (Englisch)

602917

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

CONDITION POSSIBLE CAUSES POSSIBLE SOLUTIONS

No sound from all channels. • AC power unplugged. • Check AC cable connection and outlet.

• Power not switched on.

• Outlet has no power.

• Speaker A (or Speaker B) is not activated. • Activate Speaker A (or Speaker B) by pressing

the corresponding front panel or HTR 3

button.

No sound from some channels. • Faulty/missing cables. • Check cables.

• ’Speaker Conguration’ channel (s) set to

“OFF”.

• Check ‘Speaker Conguration’ menu.

• Power-amp or speaker-connections faulty. • Check power amp, cabling, and speakers.

No sound from surround channels. • No surround listening mode is engaged. • Select appropriate listening mode.

• Surround-channels set to “OFF” on ‘Speaker

Conguration’ menu.

• Correct ‘Speaker Conguration’ or ‘Speaker

Levels’ settings.

• Surround-channels level set too low on

‘Speaker Levels’ menu.

No sound from Subwoofer. • Subwoofer is o, not powered or improperly

connected.

• Power-up subwoofer, check Sub’s AC outlet

or check connections.

• Subwoofer set to “OFF” on ‘Speaker

Conguration’ menu.

• Correct ‘Speaker Conguration’ or ’Speaker

Levels’ settings.

• Sub level set too low on ‘Speaker Levels’

menu.

No sound from Center channel. • Source is a 2/0 (etc.). Dolby Digital or DTS

recording without center channel.

• Play a known 5.1-channel recording or select

Dolby Pro Logic IIx Music mode.

• Center set to “OFF” on ‘Speaker Conguration’

menu.

• Correct ‘Speaker Conguration’ or ‘Speaker

Levels’ settings.

• Center level set too low on ‘Speaker Levels’

menu.

No Dolby Digital/DTS. • Source’s digital output is not connected to a

T 775 digital input.

• Check connections.

• Source component not congured for

multichannel digital output.

• Check source component setup.

T 775 does not respond to HTR 3 remote. • Batteries are at or incorrectly inserted. • Check batteries.

• IR transmitter window on remote or IR A/V

Receiver window on T 775 is obstructed.

• Check IR windows and ensure clear line-of-sight

from remote to T 775.

• T 775 front panel is in very bright sunlight or

ambient light.

• Reduce sunlight/room lighting.

T 775 does not respond to front panel

commands or remote control.

• Microprocessor error.

• Power-down the T 775 via the rear panel Power

switch and unplug it from the AC outlet.

• T 775 may have over heated. • Wait ve minutes, re-connect and power up.

• 12V TRIGGER IN/OUT is set to AUTO position. • Switch 12V TRIGGER IN/OUT to OFF position.

Factory defaults for 120V version only : Press simultaneously Source

+ Front Input/MP

Factory defaults for 230V version only : Press simultaneously Source + Front Input/MP

Audyssey Auto Calibration settings along with other stored presets and settings will all be deleted upon restoring your T 775 to its factory

defaults.

REFERENCE

TROUBLESHOOTING

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 775 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 775

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info