Bedienungsanleitung NAD T 785 (Seite 27 von 52) (Englisch)

602918

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

TRIGGER SETUP

The T 785 features three congurable +12V DC Trigger Output that can be

used to activate a component or system it is fed into. A Trigger Input is also

available to turn on the applicable link it is associated to. Use a combination

of or ENTER and keys to navigate through the Trigger Setup menu

parameters.

TRIGGER OUT

Triggers are low voltage signals used to turn on/o other compliant

devices. The T 785’s three +12V DC Trigger Outputs (Trigger 1 Out, Trigger 2

Out and Trigger 3 Out) are dependent on which mode they are associated

with. There are six choices where +12V DC output can be assigned and

these are – Main, Zone 2, Zone 3, Zone 4, Zone 2+3+4 and Source Setup.

Main : +12V DC is available at the assigned Trigger Out when the T 785

is at powered state.

Zone 2, Zone 3, Zone 4, Zone 2+3+4 : When the applicable Zone is

at powered state, +12V DC is available at the assigned Trigger Out.

Source Setup : If Trigger Output is linked to ‘Source Setup,’ +12V DC

is available at Trigger Out whenever the particularly assigned Source is

selected. Please see also separate discussion about ‘Trigger Out’ under

the Source Setup (Normal) section.

DELAY

The availability of +12V DC at Trigger Out can be regulated. If it is desired

that +12V DC is available without delay the moment Trigger Out is linked

to its assigned setting, set Delay to 0s. Otherwise, one can select through a

delay time of 1s to 15s.

AUTO TRIGGER IN

Auto Trigger IN allows external system controllers to toggle the associated

section of the T 785 from ‘Standby’ to ‘On’ and vice versa. When the TRIGGER

switch at the rear panel is set to AUTO, a +12V DC input at Trigger IN will

power ON the section where Trigger IN is assigned,

Main : From standby mode, the T 785 is powered ON when +12V DC is

applied at Trigger IN.

Zone 2, Zone 3, Zone 4 : Applicable Zone is turned ON whenever +12V

DC is present at Trigger IN.

All : Main, Zone 2, Zone 3 and Zone 4 as described above will all be

activated given a +12V DC input at Trigger IN.

WARNING

 IfAutoTriggerINatTriggerSetupmenuisassignedto‘Main’or‘All’and

theTRIGGERswitchissetto‘AUTO’mode,theStandbybuttoninthe

frontpanelaswellasthecorrespondingON/OFFfunctionkeysinthe

HTRC1remotecontrolwillbedisabledeectivelyhandingthisfunction

toanexternalcontroller.SwitchTRIGGERto‘OFF’tomaintainnormal

powerON/OFFfunctionprocedures.

See also ‘Item12. +12 V TRIGGER OUT, TRIGGER IN, TRIGGER AUTO/OFF’ of

REAR PANEL discussion as well as the ‘Trigger Out’ discussion under ‘Source

Setup (Normal View).’

LISTENING MODE SETUP

The T 785 has various listening mode options and is mostly congurable.

These are provided to reproduce a variety of sound eects depending

upon the content of the source to be played. Use a combination of or

ENTER and keys to congure the following settings.

LISTENING MODES

The audio format as detected by the selected Source can be automatically

congured and processed through the following options:

DOLBY

Dolby Digital is the multi-channel digital signal format developed in the

Dolby laboratories. Discs bearing the Dolby Digital (double-D symbol) logo

were recorded with up to 5.1 channels of digital signals, reproducing a

much better sound quality, with dynamic and spatial sound sensations that

are much better than in the previous Dolby Surround.

A Dolby Digital audio input can be congured relative to its format as

follows

Stereo: If the detected audio is of Dolby stereo format, you can default

it to one of the following settings – Pro Logic, PLIIx Movie, PLIIx Music or

None.

Surround: If the detected audio is of Dolby Surround format, you can

default it to one of the following settings –Surround EX, PLIIx Movie,

and PLIIx Music, Stereo Downmix or None.

None: If ‘None’ is selected, the Dolby Digital signal will be defaulted

to the ‘Stereo’ or ‘Surround’ settings set forth at the ‘PCM’ option. See

discussion below about ‘PCM’.

OPERATION

USING THE T 785  SETUP MENU

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 785 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 785

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info