Bedienungsanleitung NAD T 785 (Seite 34 von 52) (Englisch)

602918

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

LISTENING TO AM/FM RADIO

The T 785’s internal AM/FM tuner oers very high quality sound from radio

broadcasts. The reception and sound quality will always be dependent to a

degree however on the type of antenna(s) used as well as proximity to the

broadcast origin, geography and weather conditions.

ABOUT ANTENNAS

The supplied ribbon-wire FM antenna can be connected to the rear-panel

FM-antenna input using the included ‘balun’ adapter and should be fully

extended to form a “T”. This folded-dipole antenna will usually work best

when oriented vertically, with the arms of its “T” fully outstretched and

arranged perpendicular to the origin of the desired broadcast. There are

no ‘rules’ however, and experimenting freely with antenna placement and

orientation may yield the clearest sound and lowest background noise.

In areas of poor FM reception, an exterior FM antenna can improve performance

dramatically. If radio listening is important to you, consider consulting an antenna

installation professional to optimize your system.

The supplied AM ‘loop’ antenna will usually provide adequate reception.

However, an exterior AM antenna can be used to improve reception.

Consult an antenna professional for more information.

IMPORTANT NOTICE

 Unlessotherwisespecicallystated,navigatingoraccessingAM/FM

functionscanbeundertakenbyusingeithertheHTRC1remotecontrol

orthefrontpanelbuttons.Ifthecontrolbuttonoriconbuttonbeing

referredtoisavailableontheHTRC1remotecontrolandfrontpanel,

thenthereferencetosaidbuttonisapplicabletoboththeHTRC1remote

controlandfrontpanel.Thesameconditionappliestotheirequivalent

buttons.

NOTE

 WhenusingtheHTRC1tocarryoutAM/FMcommands,ensurethatthe

DEVICESELECTORissetto“TUNER”.

ASSEMBLING THE LOOP ANTENNA

1 Rotate the outer frame of the antenna.

2 Insert the bottom edge of the outer frame into the groove on the stand.

3 Extend the antenna cord.

SELECTING A TUNER BAND

Press the [AM/FM/DB] button on the front panel or the numeric ‘+10’

button of the HTRC 1 while at AMP or TUNER device selector page. Each

subsequent press of either button will toggle you through AM, FM and XM

(or DAB) band. Stop (release button) at your desired tuner band.

TUNING STATIONS

1 Press TUNE / on the front panel momentarily to step up or down

between AM or FM frequencies.

2 Press and hold TUNE or TUNE for more than 2 seconds to search

up or down - the T 785’s tuner will stop at the next suciently strong

signal it encounters. Pressing the TUNE / during the search

process will stop the search.

3 After rst pressing ‘TUNER’ (yellow lettering) at the Device Selector page

of HTRC 1 to set the remote to control Tuner functions, press TUNE

or TUNE (yellow lettering) on the HTRC 1 – toggle in to perform

slow manual search, press and hold to automatically search.

DIRECT TUNING

If you know your desired station’s frequency allocation, you can tune

directly to the station.

1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see

the lower line of the VFD). Select “Tune” mode.

2 Using the numeric keys of the remote control, key-in the frequency

allocation of the station. For example, to enter 104.50MHz, press 1, 0, 4,

5 and 0 or press 1,0,4,5 and then [ENTER].

SETTING RADIO PRESETS

The T 785 can store a mix of your 40 favorite AM, FM and XM (or DAB) radio

stations for immediate recall.

1 To store a radio preset, rst tune the desired frequency (see above), then

press the front panel ‘MEMORY’ key.

2 The VFD will show the next available preset number (Preset _ _ Free).

If there are no more vacant Preset number, you can overwrite an

existing Preset number by pressing the buttons on the HTRC 1

(or corresponding front panel navigation buttons) to select the Preset

number you want to overwrite.

3 Then, press the ‘MEMORY’ key once again to save the station to the

particular Preset number and displaying ‘P_ _’ (the two blank spaces

will correspond to the preset number that could be from ’01’ to the

maximum of ’40’) on the VFD.

4 Press PRESET / on the front panel to step up or down between

presets. Press and hold PRESET / to “scroll” continuously up or

down. The HTRC 1 remote’s PRESET keys work similarly.

NOTE

 TheT785’sRadioPresetsaredistinctfromits‘global’Presetsthatcanbe

usedtomanagelisteningandsetupmodesandlevels.See‘A/VPresets’

above.

DIRECT RECALL OF A PRESET

You can directly recall a desired Preset number.

1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see

the lower line of the VFD). Select “Preset” mode.

2 Using the numeric keys of the remote control, key-in directly your

desired Preset number.

DELETE A PRESET

1 Select the Preset number to be deleted.

2 Press and hold [MEMORY] button and then press and release [INFO]

button – current stored preset setting will be erased. The Radio Preset

can only be deleted using the front panel buttons.

OPERATION

USING THE T 785  AM/FM/DB/iPod

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

NAD T 785 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 785

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info