Bedienungsanleitung NAD T 785 (Seite 42 von 52) (Englisch)

602918

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

For example, the grey AMP DEVICE SELECTOR key label corresponds to the

grey input-select labeling adjacent to the numeric keys: When the HTRC

1’s AMP DEVICE SELECTOR page is active, these keys select the amplier

or receiver inputs. Similarly, the red DVD DEVICE SELECTOR key label

corresponds to several red labels, the green TV DEVICE SELECTOR key to

green labels, and so on.

NAVIGATION OF THE HTRC 1 CONTROLS

DEVICE SELECTOR KEYS

Simply pressing a DEVICE SELECTOR key will change the active device on

the HTRC 1. At this time, no IR commands will be transmitted. The name of

the selected device will be shown on the rst line of the LCD display.

NOTE

 AnyIRcommandcanbeassociatedwithaDEVICESELECTORkeyduring

“Copy”and“Learn”modes.Oncetheassociatedfunctionisassignedto

theDEVICESELECTORkey,pressingandholdingtheDEVICESELECTOR

keyformorethantwosecondswillsendtheassociatedcommandin

additiontotheHTRC1switchingitsactivedevice.

MACRO KEYS

A macro can be associated with every key on the HTRC 1 except for the

MACRO button itself. A total of 52 macros can be stored. To execute a macro:

• Press the MACRO key. The rst line of the LCD display will show “MACRO.”

Within ve seconds, press the key the macro is associated with.

• While the macro is executing a small "M" will be shown in the top right

of the LCD display.

Refer also to the “MACRO” item below of the “HTRC 1 SETUP MENU” section

for information on how to setup macros.

FUNCTION KEYS

There are 44 dedicated function keys on the HTRC 1. When you press a

function key, the name of the function will be shown on the second line of

the LCD display while the command is being transmitted.

A/V PSET KEY

In the default conguration of the HTRC 1, the A/V PSET key acts as a shift

function when the AMP device is selected. Pressing the A/V PSET key

once will cause “Preset” to be displayed on the rst line of the LCD display.

If within ve seconds you then press a digit (0 – 9), the function for the

corresponding A/V Preset will be transmitted.

NOTE

 TheHTRC1isauniversal-typeremotecontrol;someNADreceiversmay

nothavemorethan5AVpresets.

SOFTWARE VERSION NUMBER

Press simultaneously the ON + TEST buttons for ve seconds to display

version numbers.

SETUP MENU

Press and hold the SETUP and ENTER keys for ve seconds to enter the

Setup Menu. You cannot enter the setup menu if the remote is currently

displaying “Low Batt.” This feature prevents the setup from becoming

corrupted under low battery conditions. Please refer to “HTRC 1 SETUP

MENU” section below for the overall structure and basic operation of the

Setup Menu.

HTRC 1 SETUP MENU

GENERAL MENU OPERATION

• Press and hold SETUP + ENTER for 5 seconds to enter setup menu.

• The MACRO key is a cancel function in all setup modes unless otherwise

noted.

• You can exit menus by selecting “Exit” or pressing the MACRO key.

• Use [ ] cursor keys to select dierent menu

• For options which can be changed, the Right and Left keys are used to

cycle through the available options. Left and Right arrows will be shown

on the display to indicate when an option can be changed.

• Press ENTER to select a menu option or conrm a value.

• While a setup menu page is being executed, the corresponding rst

letter of the selected setup feature (i.e. “L” when “Library” is the selected

SETUP) is shown in the upper right corner of the display.

The following are the SETUP menu parameters.

BATTERY

Instead of waiting until the “Low Batt” warning is displayed, you can check

the current battery level using this option. This option will show a bar graph

representing the current battery level. When the batteries are new, the bar

graph will show 8 bars. Once the bar graph reaches close to zero, the “Low

Batt” warning will start to show.

LOW BATTERY WARNING

If the HTRC 1 senses the batteries are low, it will show “Low Batt” on the

second line of the LCD display whenever the remote is idle. When this

occurs the batteries should be replaced with new ones immediately.

BACK LIGHT SENSITIVITY (B LIGHT)

The HTRC 1 is equipped with a backlight to increase visibility of the HTRC 1

in low light conditions. The HTRC 1 also includes a light sensor. By default, if

you press any key on the remote and it senses a low light condition, the back

light will turn on. It will then turn o again ve seconds after no key has been

pressed. The behavior and timeout for the backlight can be adjusted.

TIMEOUT: The backlight timeout can be set from 0 - 20 seconds. This is the

length of time the backlight stays ON after releasing the last key.

OPERATION

USING THE HTRC 1 REMOTE CONTROL

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 785 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 785

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info