Bedienungsanleitung NAD T 787 (Seite 32 von 48) (Englisch)

493493

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

The T 787’s internal AM/FM tuner oers very high quality sound from radio

broadcasts. The reception and sound quality will always be dependent to a

degree however on the type of antenna(s) used as well as proximity to the

broadcast origin, geography and weather conditions.

ABOUT ANTENNAS

The supplied ribbon-wire FM antenna can be connected to the rear panel

FM antenna input using the included “balun” adapter and should be fully

extended to form a “T”. This folded-dipole antenna will usually work best

when oriented vertically, with the arms of its “T” fully outstretched and

arranged perpendicular to the origin of the desired broadcast. There are

no “rules” however, and experimenting freely with antenna placement and

orientation may yield the clearest sound and lowest background noise.

In areas of poor FM reception, an exterior FM antenna can improve

performance dramatically. If radio listening is important to you, consider

consulting an antenna installation professional to optimize your system.

The supplied AM “loop” antenna will usually provide adequate reception.

However, an exterior AM antenna can be used to improve reception.

Consult an antenna professional for more information.

IMPORTANT NOTE

When using the HTR 8 to carry out AM/FM commands, ensure that the

DEVICE SELECTOR is set to “TUNER”.

ASSEMBLING THE LOOP ANTENNA

1 Rotate the outer frame of the antenna.

2 Insert the bottom edge of the outer frame into the groove on the stand.

3 Extend the antenna cord.

SELECTING A TUNER BAND

Press the [AM/FM/DB] button on the HTR 8 while at AMP or TUNER device

selector page. Each subsequent press will toggle you through AM, FM, XM

or DAB band. Stop (release button) at your desired tuner band.

TUNING AM/FM STATIONS

Upon selecting AM or FM band, use TUNE [ 7/8 ] on the HTR 8 to

perform slow manual search; press and hold to automatically search.

The front panel [ a/s ] or HTR 8’s [ A/S ] buttons can also be used to tune

for stations.

1 Press [ A/S ] momentarily to step up or down between AM or FM

frequencies.

2 Press and hold [ A/S ] for more than 2 seconds to search up or down - the

T 787’s tuner will stop at the next suciently strong signal it encounters.

3 Pressing the [ A/S ] during the search process will stop the search.

DIRECT TUNING

If you know your desired station’s frequency allocation, you can tune

directly to the station.

1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see

the lower line of the VFD). Select “Tune” mode.

2 Using the numeric keys of the remote control, key-in the frequency

allocation of the station. For example, to enter 104.50MHz, press “1”, “0”,

“4”, “5” and “0”.

STORING PRESETS (AM/FM/XM/DAB)

The T 787 can store a mix of your 40 favorite AM, FM and XM (or DAB) radio

stations for immediate recall.

1 To store a desired AM/FM station to a preset, rst tune to the desired

frequency (see above), then press the front panel’s [MEMORY] button.

The VFD will show the next available Preset number - for example,

“Preset 4 Free” in the lower line.

2 Press the [MEMORY] button again to store the desired frequency on the

Preset number shown (“P04” is shown in the right side of the VFD). Your

desired frequency is now stored in the assigned preset number.

NOTE

If there is no more vacant Preset number, you can overwrite an existing

Preset number by pressing the [ D/F ] buttons to select the Preset

number you want to overwrite.

DIRECT RECALL OF A PRESET NUMBER AM/FM/XM/DAB

You can directly recall a desired Preset number.

1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see

the lower line of the VFD). Select “Preset” mode.

2 Using the numeric keys of the remote control, directly key-in your

desired Preset number. For example, to enter Preset 5, press “5”.

DELETING A STORED PRESET AM/FM/XM/DAB

You can empty a preset by deleting the stored information.

1 Select the preset number to be deleted. For example, “P03”.

2 Press and hold [MEMORY] button and then press and release [INFO]

button – current stored preset setting will be erased

(“P03” becomes “P--”).

CHOOSING THE TUNER MODE

The front-panel [TUNER MODE] key is a dual-purpose control. In the normal

position (FM MUTE FM STEREO icons on the VFD are illuminated), only the

stations with a strong signal can be listened to, and the noise between

stations is muted.

Pressing the [TUNER MODE] button again (FM MUTE FM STEREO icons on

the VFD are extinguished) allows distant and potentially noisy stations to be

received. Noise is reduced if the FM station signal level is less than the FM

Stereo threshold (since mono FM is inherently less noise-prone) though at

the sacrice of the stereo eect.

NOTE

One can store the same channel in two preset locations - one with

TUNER MODE On and another with TUNER MODE O.

OPERATION

LISTENING TO AM/FM RADIO

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 787 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 787

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info