Bedienungsanleitung NAD T748v2 (Seite 31 von 40) (Englisch)

602906

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Until now, analogue radio signals such as FM or AM have been subject to

numerous kinds of interference on their way from the transmitter to your

radio. These problems were caused by mountains, high-rise buildings

and weather conditions. With Digital Audio Broadcast (DAB), you can now

receive CD-like quality radio programs without any annoying interference

and signal distortion. DAB broadcasts use digital signals rather than

traditional analogue transmissions, thus providing clear high quality

reception. You getfar more robust reception andvirtually hiss or crackle

freesound with DAB as long as you are withina good coverage area.

With DAB, the listener can scroll through a list of available stations - then

instantly tune to the station of his choice. There is no need either to

remember channel frequencies. All broadcasts are selected by simply

selecting the service name.

The T 748 makes it possible for you to enjoy listening to DAB broadcasts.

The T 748 has a Digital Audio Broadcast (DAB) module socket on the rear

panel for adding a separately sold and NAD-specied outboard DAB

module – the NAD DAB Adaptor DB 1 or the DAB+ NAD DAB Adaptor

DB 2. All the control software for this format is included; just plug-in the

module and start enjoying the CD-like quality sound and expansive content

selection available with DAB.

IMPORTANT NOTICE

Unless otherwise specically stated, navigating or accessing DAB

functions can be undertaken by using either the AVR 4 remote control

or the front panel buttons. If the control button or icon button being

referred to is available on the AVR 4 remote control and front panel,

then the reference to said button is applicable to both the AVR 4 remote

control and front panel.

NOTES

• WhenusingtheAVR4remotecontroltocarryoutDABcommands,

ensure that the DEVICE SELECTOR is set to “TUN”.

• AtDABmodeandwithDEVICESELECTORsetto“TUN”,AVR4’s[TUNER

MODE] button has the same function as that of front panel’s [MENU]

button.

• IntheDABdiscussionsbelow,allcontrolbuttonsmentionedarewith

reference to the AVR 4 remote control.

CONNECTING THE DAB MODULE

Plug-in the other end of the DIN connector (supplied with your NAD DAB

Adaptor) from the DAB module’s output port into the corresponding DAB

module input socket on the rear panel of the T 748. Select DAB mode on

the T 748 by toggling the [AM/FM/DB] button in the AVR 4 remote control.

NOTES

• TheNADDABAdaptor(DB1orDB2)isnotsuppliedwithyourT748.

• RefertotheinstallationdiagramprintedonthecartonboxoftheNAD

DAB Adaptor for guidance on how to connect the NAD DAB Adaptor to

the T 748.

• IfthereisnoNADDABAdaptorconnected,theVFDwillshow“Check

DAB Tuner”.

DAB OPERATION

With the separately sold NAD DAB Adaptor already connected to the T 748,

you can now carry out the T 748 to receive DAB broadcasts.

1 Toggle [AM/FM/DB] button until DAB mode. When DAB mode is

selected, VFD will show “DAB Initialize Please wait” and then go to “Full

scan” mode. “Full Scan” will take at least 20 seconds or more to complete.

FULL SCAN will enable the scanning of the full range of digital

frequencies (Band III and L-Band). This sequence cannot be interrupted.

�DAB�Initialize�

�Please�wait��

Full scan��5

>>>>>>>>>>>>>>>>

The arrows show the progress of the sequence. When scanning is

completed, the last number shown on the upper right side of the VFD

corresponds to the total number of DAB broadcast stations found. Then,

the rst station is tuned in (See “ALPHANUMERIC” description below to

understand the order or arrangement of stations).

2 The strength of the incoming signal can be shown on the VFD by

pressing the [ENTER] button. The more “o” segments visible in the lower

display line, the stronger the signal. By changing the position of the

antenna, you can increase the signal strength. Consult an antenna

professional for more information.

DAB��

oooooooooooooooo

“No Service List” will be shown in the VFD when no DAB stations are

found after the scanning process. If this occurs, check the connection

and position of the DAB antenna or call your local DAB broadcast

providers for coverage information.

DAB��

No�Service�List�

SERVICE LIST

Follow the steps below to select through the DAB service stations found.

1 At DAB mode, press [ A/S ] to step through the list of available stations

as shown in the lower display line of the VFD.

DAB��

<EDGE�102��>

2 Press [ENTER] to select the desired station.

OPERATION

LISTENING TO DAB RADIO

ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T748v2 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T748v2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info