Bedienungsanleitung NAD T977 (Seite 7 von 66) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch)

602921

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

3 SPEAKER

· The T 977 is equipped with special high-current binding-post

speaker terminals. Connect the respective SPEAKER FRONT L, FRONT

R, CENTER, SURR R, SURR L, SURR-BL and SURR-BR channels to their

corresponding loudspeakers. Make sure the “+” (red) terminal and

“-” (black) terminal are connected to the corresponding “+” and “-”

terminals of the loudspeaker. Use extra care to ensure that no stray

wires or strands cross between posts or terminals at either end.

· Always use heavy duty (16 gauge; 1.5mm, or thicker) stranded

wire to connect loudspeakers to your NAD T 977. The high-current

binding post terminals can be used as a screw terminal for cables

terminating in spade or pin sockets or for cables with bare wire

ends.

· The T 977 is designed to produce optimum sound quality when

connected to speakers with impedances within its operating range.

Please make sure that all the speakers are rated 4 ohms minimum

per speaker.

NOTE

Use stranded wire of at least 16 gauge (AWG). Connections to the T 977

can be made with banana plugs (120V version only) or by using bare

wire or pins. Use the transverse hole through the post for bare-wire or

pin connections. By loosening the terminal’s plastic nut, make a clean,

neat connection and re-tighten carefully. To minimize the danger

of short-circuit, ensure that only 1/2-inch of exposed wire or pin is

employed when connecting.

4 GROUND TERMINAL

· The T 977 is provided with a GROUND terminal on the rear panel.

This terminal is connected directly to the chassis of the T 977.

· Use this terminal to properly ground the T 977. A ground lead wire

(not supplied) or similar can be used to connect the T 977 to ground

via this ground terminal. After insertion, tighten the terminal to

secure the lead.

5 SOFT CLIPPING

· Enables NAD’s proprietary Soft Clipping circuitry on all channels. At

“ON” position, Soft Clipping gently limits the output of the T 977 to

minimize audible distortion should the amplier be over-driven.

· Soft Clipping may simply be left ON at all times to reduce the

likelihood of audible distortion from excessive volume settings.

However, for critical listening and to preserve optimum dynamics,

you may wish to defeat it by setting this switch to “OFF” position.

· The SOFT CLIPPING indicator on the front panel will illuminate when

the amplier is in Soft Clipping mode.

6 +12V TRIGGER IN

· The +12V Trigger input allows the T 977 to be switched remotely

from standby mode to ON and vice-versa by ancillary equipments

such as a preamplier, AV processor, etc. The controlling device

must be equipped with a 12V trigger output to use this feature.

WARNING

The front panel Standby button is disabled as long as the male plug

of the mono cable (with or without +12V DC) is connected to T 977’s

+12V TRIGGER IN. Unplug the mono cable for the T 977 to be normally

switched ON (or back to standby mode) using the front panel STANDBY

button.

7 FUSE HOLDER

· In the unlikely event a fuse needs to be replaced, unplug the mains

power cord from the wall. Then, remove all connections from the

amplier. Use a athead screw driver or similar to open the fuse

holder via the slot indicated. With the screw driver in place, push

and turn counterclockwise to open the fuse holder.

· Only replace the fuse with the same type, size, and specication.

IMPORTANT NOTICE

Do not use any substitute fuses of dierent types or with dierent ratings

or values. Failure to observe this precaution may cause damage to the

amplier circuits and may create a re hazard and/or defeat the safety

built into the amplier and may void the warranty.

8 AC MAINS INPUT

· The T 977 comes supplied with a separate detachable mains power

cord. Before connecting the plug to the mains powers source,

connect rmly rst the other end to T 977’s AC Mains input socket.

· Connect only to the prescribed AC outlet, i.e., 120V 60 Hz (for 120V

version models only) or 230V 50 Hz (for 230V version models only).

· Always disconnect the mains power plug from the mains power

source rst, before disconnecting the cable from the T 977’s AC

Mains input socket

POWERDRIVE

The T 977 uses NAD’s proprietary PowerDrive™ amplier technology for

all channels to preserve accurate, linear reproduction regardless of the

loudspeaker. This uniquely ecient power-supply topology provides the

real-world benets of high dynamic power that remains uncompromised

by low-impedance speakers.

By adding a second high-voltage rail to our well regulated high-current

power supply, we get an “overdrive” that can nearly double the continuous

power on a short term dynamic power basis. PowerDrive oers greater

amplier stability and low impedance drive capability, resulting in less

distortion when driving real speakers with real program material.

IDENTIFICATION OF CONTROLS

REAR PANEL

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

T977_eng_OM_v04.indd 7 17/04/2012 9:28am

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T977 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info