Bedienungsanleitung NAD Viso 1 (Seite 7 von 12) (Englisch)

493484

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

FIRST TIME USE

Out of the box and connecting the VISO 1 AP to the mains power source for

the rst time, the “S” indicator will alternately switch to green and red light

after initializing. This indicates that the VISO 1 AP is ready to be congured.

Refer to the following sections to fully enjoy and appreciate your VISO 1 AP.

SETTING UP NETWORK CONNECTION

AirPlay lets you stream music from your AirPlay-enabled device to the VISO

1 AP. The AirPlay-enabled device and the VISO 1 AP must be in the same

network to send and receive streaming audio with AirPlay.

The VISO 1 AP can be connected to a network using any of the following

methods

A Wired connection

B Wireless connection

C Share Wi-Fi setting

Start playback of your device after successful network connection using any

of the above methods.

WIRED CONNECTION

Network connection using Ethernet broadband connection. Set up a Wired

Ethernet broadband router with broadband internet connection. Your

router or home network should have a built-in DHCP server to consummate

the connection.

• Using a standard straight-through Ethernet cable, connect one end of

the Ethernet cable (not supplied) to the LAN port of your wired Ethernet

broadband router and the other end to VISO 1 AP’s LAN port.

• The ”S” indicator will turn to solid green upon successful network

connection.

It is advisable that wired connection is utilized when possible. Wired

connection is less likely to have “drop-out” or range problem and not

vulnerable to interference or eavesdropping.

WIRELESS CONNECTION

Wireless (WiFi) broadband router with broadband internet connection is

required for wireless connection to be established. Wireless connection for

VISO 1 AP can be setup by the following procedure.

1 Press and hold “S” until it turns ashing green – this indicates it is in

Access point/setup mode already.

2 Using your iOS device (iPad is used here for reference), select among

the list of available network connections the unique network ID (NAD_

VISO1_DF601A in this example) of your VISO 1 AP.

3 Launch Safari and enter http://192.168.1.12 . The VISO 1 AP User

Interface menu window will appear. Select Prole Conguration.

4 Select your local network from the drop down SSID list (NADLAB

(WPA2 TKIP+CCMP) in this example).

NOTES

• The Status Information displays current details about your VISO 1 AP

like connection status, signal strength, rmware version and others.

If your VISO 1 AP is congured already, locate and access the TCP/IP

address of your VISO 1 AP to check Status Information.

• Firmware Update is not for consumer use- this is restricted to authorized

NAD service personnel and distributors.

5 Type the WPA Passphrase (if it is password protected) of your local

network in the eld provided and then select Apply to join in.

VISO 1 AP OPERATION

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD Viso 1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD Viso 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info