Bedienungsanleitung Naim NAP 200 DR (Seite 30 von 44) (Englisch)

707507

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

E28

Preamplifier and Integrated Amplifier Operation

28 Preamplifier and Integrated Amplifier Operation

Many operational and control features of Naim preamplifiers and integrated amplifiers

are common to all and are based on a similar user interface. This section of the manual

describes those features and the user interface, drawing attention to differences between

products where they occur. Table 28.10 sets out some variations in user interface between

products.

Front panel controls are duplicated on the remote control handset which may also

provide some extra functions. See Sections 29 and 30 for more information.

For the purposes of brevity the term preamplifier in the following paragraphs can be taken

also to mean integrated amplifier.

28.1 Automatic Input Switching

With Automatic Input Switching engaged the appropriate

source input will be selected as soon as any handset function

for that (Naim) source component is operated. For example,

if the tuner input is selected and the cd play key is pressed on

the handset, the preamplifier will automatically switch to the

cd input. Automatic Input Switching can be programmed to

operate on any combination of the cd, av, hdd and tuner

input buttons (and sockets to which they are assigned).

To enable Automatic Input Switching, first switch the

preamplifier into program mode by pressing and holding

the handset prog key (with the handset in preamplifier

mode). The front panel source mono/mon button (NAC

202 mon and NAC 152 XS mute buttons, Supernait record

mute button, Nait XS mute button and Nait 5i hdd button)

will illuminate if automatic switching is already enabled. If it

is not enabled it can be switched on by pressing the same

button.

With automatic switching enabled, pressing the button

again will reveal the inputs selected for auto switching

by their indicators illuminating for a short time. Repeated

operation of the button will sequentially select through

each possible combination of cd, av, hdd, and tuner inputs

and auto switching disabled (all indicators off). When the

desired inputs selected for auto switching are indicated,

stop pressing the button.

Automatic Input Switching only becomes operational

on exit from program mode by pressing and holding the

handset prog key.

Note: The preamplifier will leave program mode

automatically if no control commands are received for five

minutes.

Note: In a few cases some further equipment configuration

may be required for auto switching to operate correctly.

Please contact your retailer or local distributor for advice.

28.2 AV Integration (Unity Gain)

Unity Gain enables an audio-visual processor to be

integrated such that its volume control takes over command

of signals connected to selected preamplifier inputs. On the

NAC 552 Unity Gain may be selected on DIN input sockets 4

and 5. On all other preamplifiers it may be selected on only

the av input.

To select Unity Gain, first switch the preamplifier into

program mode by pressing and holding the handset prog

key (with the handset in preamplifier mode). The front

panel source mute button (NAC 202 mute button, NAC

152 XS and Nait 5i av button) will illuminate if Unity Gain

is selected. If it is not enabled it can be switched on by

pressing the same button twice.

Note: Unity Gain (AV Bypass) on the Nait XS is not engaged

in program mode but via a rear panel switch.

With Unity Gain enabled on the NAC 552, pressing the

source mute button again will reveal the inputs selected

by their indicators illuminating for a short time. Repeated

operation of the button will sequentially select each

combination of the available inputs, and Unity Gain

disabled. When the desired inputs are indicated, stop

pressing the button. The selected inputs will then be

enabled for Unity Gain. The handset can also be used to

select Unity Gain. See table 28.10.

Unity Gain only becomes operational on exit from program

mode by pressing and holding the handset prog key.

Note: The preamplifier will leave program mode

automatically if no control commands are receved for five

minutes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim NAP 200 DR Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim NAP 200 DR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info