707507
11
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
E9
NAP 200
12. NAP 200 Installation and Operation
The NAP 200 should be installed on a dedicated equipment stand intended for the purpose and should be in its nal location
before connecting cables or switching on. Switch on the source and preamplier components, with the volume turned down,
before switching on the NAP 200. The NAP 200 power button is located on the front panel.
The NAP 200 can provide power for an appropriate Naim Audio preamplier. The power supply output is carried on the DIN
input socket.
The NAP 200 is heavy and care should be taken when lifting or moving it. Make sure that the surface it is to be placed on can
support its full weight.
12.1 General Connections Notes
The negative input and output connections are all common.
The mains earth should always be connected regardless of
what other equipment is used. This only grounds the case
and the electrostatic screen within the transformer, and is
not connected to the signal negative. In order to avoid hum
loops, the signal negative of the whole system should be
connected to the mains earth (ground) in one place.
12.2 Protection Notes
If the ampliers external case reaches 70°C due to
prolonged running at high power, the mains supply will be
interrupted and the illuminated logo will switch o until
the amplier has cooled down. This may take up to thirty
minutes.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME
LEVEL. YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS
THE CASE. THE VOLUME SHOULD BE REDUCED.
12.3 Loudspeaker Cable and Connectors
Only Naim Audio speaker cable should be used to connect
a loudspeaker to the output of the NAP 200. Custom Naim
Audio loudspeaker connectors are supplied to make the
connection and in order to comply with current European
safety regulations these should always be used.
DAMAGE TO THE AMPLIFIER MAY RESULT IF “HIGH
DEFINITION” CABLE OR ANY OTHER SPECIAL CABLE IS
USED TO CONNECT THE LOUDSPEAKERS.
Ensure when connecting speakers that they are “in phase.
That is, the positive and negative connection orientation at
both the speaker and amplier ends of the cable is the same
for both channels.
FUSE RATING: ANTISURGE
100V TO 120V: T6.3AL.
200V TO 240V: T3.15AL/250V.
AC ONLY
FREQUENCY: 50/60Hz
INPUT POWER: 140VA
ch1 left+
+
WARNING:
DO NOT REPLACE SUPPLIED LOUDSPEAKER
PLUGS WITH INDIVIDUAL 4mm PLUGS
LoudspeakerPower Input
-ve
ch2
+24V 0.3A
ch1
ch2 right
WARNING:
DO NOT REPLACE SUPPLIED LOUDSPEAKER
PLUGS WITH INDIVIDUAL 4mm PLUGS
-
-
Loudspeaker
WARNING:
DISCONNECT SUPPLY CORD
BEFORE OPENING
ATTENTION:
DEBRANCHER AVANT D’OUVRIR
WARNING:
THIS APPARATUS MUST
BE EARTHED
DESIGNED AND MADE IN ENGLAND BY NAIM AUDIO LTD.
SOUTHAMPTON ROAD, SALISBURY
NAP 200
PLEASE READ THE MANUAL BEFORE USE
CONFORMS
TO EN 60065
S/No.
E2378
DR
13. NAP 200 Connections
13.1 NAP 200 Rear
+V
ch2
-ve
ch1
24V
0.3A
Input/Preamp
Power Output
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Naim NAP 200 DR wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Naim NAP 200 DR

Naim NAP 200 DR Bedienungsanleitung - Deutsch - 44 seiten

Naim NAP 200 DR Bedienungsanleitung - Englisch - 44 seiten

Naim NAP 200 DR Bedienungsanleitung - Französisch - 44 seiten

Naim NAP 200 DR Bedienungsanleitung - Italienisch - 46 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info