Bedienungsanleitung Naim NAP 250 DR (Seite 24 von 44) (Englisch)

707508

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

E22

NAIT XS Integrated Amplifier

22 NAIT XS Introduction, Installation and Connections

The NAIT XS should be installed on a dedicated equipment stand intended for the

purpose. Do not stand it directly on top of another item of equipment. Care should

be taken to ensure that it is level. The amplifier should be installed in its final location

before connecting cables or switching on. Ensure that the volume is turned down before

switching on.

A variety of power supply upgrade, alternative preamplifier and alternative or additional

power amplifier options are possible for the NAIT XS. Diagrams illustrating the connection

of some of these are shown in Section 23. Contact your local retailer or distributor for

advice on further alternative connection schemes.

The NAIT XS incorporates an AV Bypass switch on its rear panel. The switch should only

be set to “On” if the amplifier is to be used in conjunction with an AV processor in a

home theatre system. In all other installations the AV Bypass switch should be set to “Off”.

Speaker and/or amplifier damage may occur if a signal is inadvertently connected to the

NAIT XS av input while the AV Bypass switch is “On”.

Operational features common to all preamplifiers and integrated amplifiers are described

in Section 28.

22.1 Mains Power Connection

Connect the NAIT XS to a mains power socket using either

the mains cable supplied or a Naim Power-Line.

22.2 Signal Inputs

The NAIT XS front panel input buttons select the source

input signal to be routed to the integral power amplifier

and the loudspeakers. The six buttons are labelled cd,

tuner, hdd, av, aux 1 and aux 2.

The cd, tuner, hdd and av input buttons select parallel DIN

and RCA phono input sockets on the rear panel.

Note: The hdd and av sockets carry both inputs and

outputs. See Section 22.4 for more information.

The aux 1 input button corresponds to a pair of RCA

phono sockets on the rear panel and a parallel 3.5mm

stereo jack socket on the front panel. Insertion of a plug

into the front panel aux 1 socket will automatically switch

the amplifier to that input. Removal of the plug will return

the amplifier to the previously selected input. If a different

input is selected while a plug is inserted removal of the

plug will not cause the input to change.

The aux 2 input button corresponds to a DIN input socket

on the rear panel. The aux 2 DIN socket also carries a

power supply output suitable to power a Naim

Stageline

SuperLine phono preamplifier.

Note: For optimum sound quality DIN sockets should be

used in preference to RCA phono sockets.

Note: Where an input has DIN or Phono socket options only

one should be connected at any one time.

Always use high quality interconnect cables to connect

sources to inputs. The Naim Hi-Line will produce the best

results.

22.3 Speaker Outputs

A set of stereo speaker connection sockets is provided on

the rear panel. Custom Naim loudspeaker connectors are

supplied to make the connection and in order to comply

with current European safety regulations these should

always be used. Naim speaker cable will provide the best

results, however, a wide range of speaker cable types can

be used without risk of damage to the amplifier.

Ensure when connecting speakers that they are “in

phase”. That is, the positive and negative connection

orientation at both the speaker and amplifier ends of the

cable is the same for both channels.

22.4 AV and hdd Inputs and Outputs

The NAIT XS av and hdd inputs have associated outputs

that enable the selected input signal to be routed

externally; to an audio recording component for example.

Note: The av or hdd outputs will be muted if their

corresponding inputs are selected.

22.5 AV Bypass

The NAIT XS can be integrated within a multi-channel

home theatre system, driving the front left and right

channel speakers, by engaging its AV Bypass mode. AV

Bypass mode enables a home theatre processor to take

over volume control of signals connected to the NAIT XS av

input. It is engaged using the switch on the rear panel. The

NAIT XS volume control indicator will extinguish when AV

Bypass mode is engaged and the av input is selected. The

remote handset volume control will also be disabled.

Operational features

common to all

preamplifiers and

integrated amplifiers

are described in

Section 28

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim NAP 250 DR Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim NAP 250 DR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info