Bedienungsanleitung Naim NAP S1 (Seite 8 von 20) (Englisch)

707511

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

2.2 NAC S1 CONNECTION PANEL

E2378

2.3 NAC S1 AUDIO OUTPUTS AND CONNECTIONS

The NAC S1 preamplifier is fitted with two pairs of analogue stereo audio outputs: one pair of 4-pin

DIN sockets and one pair of balanced XLR sockets. A slide switch on the connection panel enables

the selection of the XLR, DIN or both output sockets.

If the NAC S1 is to be used with a Nim 500 Series or Classic Series power amplifier (most likely

a NAP 500 or NAP 300), the left and right DIN output sockets should be connected to the power

amplifier channel 1 and 2 inputs respectively using Nim 4-pin DIN to XLR interconnect cables.

Your Nim retailer will be able to supply appropriate cables. The output socket switch should be

in the DIN position.

If the NAC S1 is to be used with a pair of NAP S1 power amplifiers, the left and right balanced XLR

output sockets should be connected to the left and right power amplifier inputs using the XLR to

XLR interconnect cables supplied with the power amplifiers. If longer cables are required your

Nim retailer will be able to provide cables of the desired length. The output socket switch should

be in the BAL position.

If the NAC S1 is to be used with both Classic Series power amplification and a pair of NAP S1 power

amplifiers simultaneously, the left and right balanced XLR output sockets should be connected to

the left and right NAP S1 inputs using XLR to XLR interconnect cables. The the left and right DIN

output sockets should be connected to the Classic Series power amplifier channels 1 and 2 inputs

respectively using Nim 4-pin DIN to XLR interconnect cables. The NAC S1 output socket switch

should be in the DIN+BAL position.

DIN inputs: 1, 2 & 3

Phono inputs: 4, 5 & 6

Upper sockets: Left

Lower sockets: Right

Outputs:

XLR: balanced

DIN: unbalanced

Control:

RJ45: CAN bus x 3

RS232 × 1

Jack: Trigger in x 1

Trigger out x 2

IR in x 1

USB: Firmware update

Balanced XLR inputs:

7 & 8

Mains power and fuse

Input indicator

Output socket

selection switch

Auxiliary signal ground

connector

Power switch

2.0 NAC S1 PREAMPLIFIER

Each of the five NAC S1 inputs can be independently adjusted for input gain. Input gain

adjustment enables signal levels from different source components to be compensated so that

switching inputs is less likely to require preamplifier volume adjustment. Adjustment of input

gain is described in Section 4.2.

A signal ground terminal on the NAC S1 connection panel enables the termination of specialist

interconnect cables with auxiliary ground conductors. Contact your Nim retailer for advice on

using such interconnect cables.

Always use interconnect cables intended for high-end audio applications to connect source

equipment to the NAC S1 inputs. Nim interconnect cables will always provide the best results.

Input gain and mapping set

14 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim NAP S1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim NAP S1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info