Bedienungsanleitung Naim SUPERNAIT 2 (Seite 6 von 22) (Englisch)

707503

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Note: The AV Bypass feature must be used with care. It

bypasses the SUPERNAIT 2 volume control leaving any

signal connected to the av input to be passed to the

speakers at full volume.

Note: Inserting a headphone plug while AV Bypass

mode is selected temporarily returns the SUPERNAIT 2

to normal operation. Removing the headphone plug will

return the SUPERNAIT 2 to AV Bypass mode.

Note: The mute function is disabled when AV Bypass

mode is engaged.

4.7 Other Signal Inputs and Outputs

The SUPERNAIT 2 incorporates DIN bi-amp (output), RCA

phono sub out, DIN pre-amp out, and DIN power-amp in

sockets on its rear panel. In normal use the pre-amp out and

power-amp in sockets are connected by a link plug. The link

plug should be removed only in the following circumstances:

• A power supply upgrade is to be used.

• An alternative preamplier is to be used with the

SUPERNAIT 2 power amplier. See Section 4.8

• An alternative power amplier is to be used with the

SUPERNAIT 2 preamplier.

Note: The power amp in socket carries a 24V DC power

supply output intended for Naim preampliers that

require an external power supply.

The SUPERNAIT 2 DIN bi-amp output socket provides a

preamp output signal that enables a second power amplier

to be used in conjunction with the SUPERNAIT 2 power

amplier.

The RCA phono sub out sockets provide a stereo output

intended for connection to an active subwoofer. The output

signal is a duplicate of the preamplier output. No low-pass

ltering is applied.

Diagrams 6.1,and 6.2 illustrate some applications of the

SUPERNAIT 2 preamp out, power amp in and bi-amp

sockets.

4.8 Power Amp Mode Operation

If a SUPERNAIT 2 is to be used as a stereo power amp only it

must be congured to operate in power amp mode:

• With the SUPERNAIT 2 switched o, remove its rear

panel link plug and connect the interconnect cable

from the preamp or preamp power supply to the power

amp in socket

• Switch on the SUPERNAIT 2. The mute button will

ash to indicate that the link plug has been removed.

Press and hold the mute button until it extinguishes.

The SUPERNAIT 2 is now in power amp mode. Its

volume control indicator and button illumination will

extinguish.

• To return the SUPERNAIT 2 to normal operation, switch

it o, replace the link plug and switch it on again.

4.9 Power Supply Upgrades

The SUPERNAIT 2 preamplier can be upgraded through

the connection of an external Flatcap, Hi-Cap or Supercap

power supply. The SUPERNAIT 2 and external power

supply must be switched o when connections are made.

Switch on the external power supply rst followed by the

SUPERNAIT 2 when all connections are complete.

4.10 General Connections Notes

The SUPERNAIT 2 negative input and output connections for

each channel are common. The mains earth (ground) should

always be connected regardless of what other equipment is

used in conjunction with the amplier. The mains earth only

grounds the case and the electrostatic screen within the

transformer, and is not connected to the signal negative. In

order to avoid hum loops, the signal negative of the whole

system should be connected to the mains earth (ground) in

one place.

A signal ground connection is tted to the SUPERNAIT

2 rear panel. This is intended to be used to connect a

turntable pick-up arm signal earth only.

4.11 External Control and Interface

The SUPERNAIT 2 is tted on its rear panel with a 3.5mm

jack Remote In socket and a mini-USB interface socket.

The Remote In socket can be used for RC5 remote control

of the SUPERNAIT 2 via a wired connection or a remote IR

repeater.

The mini-USB socket enables rmware upgrades and

diagnostic tests to be carried out. Contact your Naim

retailer for more information if required.

Note: The mini-USB interface is not intended for the

connection of USB memory devices.

SUPERNAIT 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim SUPERNAIT 2 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim SUPERNAIT 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info