Bedienungsanleitung Naim SUPERNAIT 3 (Seite 5 von 22) (Englisch)

707504

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

4. SUPERNAIT 3

The SUPERNAIT 3 is a very high performance stereo integrated amplier that combines a

preamplier providing ve line-level analogue inputs and one moving magnet phono input with

a power amplier rated at 80 Watts per channel. The SUPERNAIT 3 can be controlled by either

its remote handset or by front panel mounted volume and balance knobs, and mute and input

selection buttons. The SUPERNAIT 3 remote handset is described in Section 15 of this manual.

A front panel 6.3mm jack socket enables the use of headphones with the SUPERNAIT 3.

A variety of power supply upgrade, alternative preamplier and alternative or additional power

amplier options are possible for the SUPERNAIT 3. Diagrams illustrating the connection of

some of these are shown in Section 6. If no power supply or alternative amplier options are to

be employed, the SUPERNAIT 3 preamp/power amp link plug, supplied in the accessory pack,

must be tted to the rear panel “preamp out” and “power amp in” sockets. The link plug is

shown tted in Diagram 5.2.

Your SUPERNAIT 3 should be installed on a dedicated equipment stand intended for the

purpose. Do not stand it directly on top of another item of equipment. Care should be taken to

ensure that it is level. The amplier should be installed in its nal location before connecting

cables or switching on. Ensure that the volume is turned down before switching on.

4.1 Mains Power Connection

Connect the SUPERNAIT 3 to a mains power socket using

either the mains cable supplied or a Naim Power-Line.

4.2 Signal Inputs

The SUPERNAIT 3 front panel input buttons select the

source input signal to be routed to the integral power

amplier and the loudspeakers headphones. The six buttons

are labelled cd, tuner, stream, av, phono and aux.

The cd, tuner, stream and av input buttons correspond to

parallel DIN and RCA phono input sockets on the rear panel.

The phono input button corresponds to a pair of rca phono

sockets compatible with moving magnet (mm) cartridges.

The turntable earth lead should be connected to the ground

terminal when this input is being used.

Note: The stream and av sockets carry both inputs and

outputs. See Section 4.4 for more information.

The aux 2 input button corresponds to a DIN input socket

on the rear panel. The aux 2 DIN socket also carries a power

supply output intended to power a Naim StageLine or

SuperLine phono preamplier.

Note: For optimum sound quality DIN sockets should be

used in preference to RCA phono sockets.

Note: Where an input has DIN and phono socket options

only one should be connected at any one time.

Always use high quality interconnect cables to connect

sources to inputs. The Naim Hi-Line will produce the best

results.

4.3 Speaker Outputs

A set of stereo speaker connection sockets is provided on

the rear panel. Custom Naim loudspeaker connectors are

supplied to make the connection and in order to comply

with current European safety regulations these should

always be used. Naim speaker cable will provide the best

results, however, a wide range of speaker cable types can

be used without risk of damage to the amplier.

Ensure when connecting speakers that they are “in phase”.

That is, the positive and negative connection orientation at

both the speaker and amplier ends of the cable is the same

for both channels.

4.4 av and stream Outputs

The SUPERNAIT 3 av and stream inputs have associated

outputs that enable the selected input signal to be routed

externally; to an audio recording component for example.

Note: The av and stream outputs remain active while

their corresponding inputs are selected. Take care that

a feedback loop is not inadvertently created by the

simultaneous selection of input and output.

4.5 Headphone Output

The SUPERNAIT 3 headphone output is able to drive most

headphone types. The 6.3mm (1/4”) jack socket, rather

than the smaller 3.5mm jack socket, provides more reliable

connection and potentially higher sound quality. Most

high-quality headphones are supplied with an adaptor that

enables use with either 3.5mm or 6.3mm sockets. Inserting a

headphone plug will mute the SUPERNAIT 3 speaker outputs.

Removing the headphone plug will restore the outputs.

4.6 AV Bypass

The SUPERNAIT 3 can be integrated within a multi-channel

home theatre system, driving the front left and right

channel speakers, by engaging its AV Bypass mode. AV

Bypass mode enables a home theatre processor to take over

volume control of signals connected to the SUPERNAIT 3 av

input. It is engaged using the switch on the rear panel. The

SUPERNAIT 3 volume control indicator will extinguish when

AV Bypass mode is engaged and the av input is selected.

The remote handset volume control will also be disabled.

Note: The SUPERNAIT

3 incorporates an AV

Bypass switch on its rear

panel. The switch should

only be set to “On” if the

amplifier is to be used

in conjunction with an

AV processor in a home

theatre system. In all

other installations the

AV Bypass switch should

be set to “Off”. Speaker

and amplifier damage

may occur if a signal is

inadvertently connected

to the SUPERNAIT 3 av

input while the AV Bypass

switch is “On”.

Naim SUPERNAIT 3 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim SUPERNAIT 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info