Bedienungsanleitung Napoleon BILEX 485 (Seite 18 von 56) (Englisch, Französisch)

637911

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

www.napoleongrills.com

BI ACCESSORY DRAWER INSTRUCTIONS

BI ACCESSORY DOOR INSTRUCTIONS

1. Unpack the drawer frame assembly.

2. Remove the drawers from the enclosure by fully extending them and then liing up to remove them from

the slides.

3. Shim the opening to ensure that the enclosure ts snuggly into the opening. Ensure that the side shims

are located at the same height as the enclosure mounng holes. The boom of the opening may need to be

shimmed as well to ensure that the front of the enclosure is plumb.

4. Once the enclosure is level and square, fasten into place. (Fasteners not included).

5. Re-install the drawers by pping the back of the drawer down into the slide. Once the wheels are inserted

into the slide, lower the front of the drawer unl it is level, then push in. Note: if the enclosure is installed

with shims that are too thick, the wheel will not engage into the slide. The shim thickness will need to be

reduced.

6. Remove the protecve coang from all remaining surfaces.

1. Unpack the door and frame.

a. For the curved stainless steel doors, remove the door(s) from the frame by liing the door while holding on

to the pivot rod. This will allow the pivot rod to come out of the hole on the boom of the frame. Once the

pivot is removed from the boom hole, the enre door can be dropped and removed from the frame.

b. For the PF style stainless steel door, the door needs to be removed by loosening the center philips screw on

the hinge furthest away from the door. This will allow the hinge to separate.

c. For double door kits N370-0502-1/N370-0503-1, refer to the instucons included with the door kit.

2. Center the frame in the opening. Mark the locaon of the pivot holes, top and boom. Remember on the

PT600 double doors, there will be a pivot rod on both ends. The PF style doors do not have pivot rods. Once

all pivot holes are marked, remove the frame and using a 3/8” drill bit, drill out the clearance holes for the

pivot rod. These clearance holes should be at least 1/2” deep. Aer the holes are complete, you may once

again center the frame in the opening. Starng with the hinged side, shim between the frame and side wall

of the opening. Ensure the shims are close to the hinge on the PF style doors. When the frame side wall is

plumb, fasten it to the cabinet with screws (not provided). Aach the other side of the frame in the same

fashion, ensuring the frame is square.

3. Other than on the curved stainless steel double door kit, fasteners are not required on the top and boom

of the frame. The curved stainless steel double door frame must be fastened in the center both at the top and

boom.

4. Once the frame has been secured and checked for squareness, the door can be re-installed.

5. Remove the protecve coang from all remaining surfaces.

BILEX485 BUILT-IN INSTRUCTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Napoleon BILEX 485 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Napoleon BILEX 485

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info