Bedienungsanleitung Napoleon BISB 245 (Seite 12 von 40) (Englisch, Französisch)

637932

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

www.napoleongrills.com

Troubleshoong

Problem Possible Causes Soluon

Low heat / Low ame

when valve turned

to high.

For propane - improper lighng

procedure.

For natural gas - undersized

supply line.

For both gases - improper

preheang.

Ensure lighng procedure is followed carefully. All

gas grill valves must be in the o posion when the

tank valve is turned on. Turn tank on slowly to allow

pressure to equalize. See lighng instrucons.

Pipe must be sized according to installaon code.

Preheat grill with both main burners on high for 10 to

15 minutes.

Excessive are-ups/

uneven heat.

Sear plates installed incorrectly.

Improper preheang.

Excessive grease and ash build on

sear plates and in drip pan.

Ensure sear plates are installed with the holes towards

the front and the slots on the boom. See assembly

instrucons.

Preheat grill with both main burners on high for 10 to

15 minutes.

Clean sear plates and drip pan regularly. Do not line

pan with aluminum foil. Refer to cleaning instrucons.

Burners burn with

yellow ame,

accompanied by the

smell of gas.

Possible spider web or other

debris, or improper air shuer

adjustment.

Thoroughly clean burner by removing. See general

maintenance instrucons. Open air shuer slightly

according to combuson air adjustment instrucons.

(This must be done by a qualied gas installer.)

Burner will not light

with the igniter,

but will light with a

match.

Dead baery / or installed

incorrectly.

Loose electrode wire.

Wrong replacement igniter.

Improper gap at electrode p.

Liing ames on burner.

Replace with heavy duty ‘AAA’ baery.

Check that electrode wire is rmly pushed onto the

terminal on the back of the igniter.

One spark systems must use a one spark igniter.

Ensure that the collector box is ght and the gap

between the electrode end and the collector box is

between 1/8” - 3/16” (3mm-5mm). The gap can be

adjusted by bending the box in or out.

Close air shuer slightly - see previous problem.

“Paint” appears to be

peeling inside lid or

hood.

Grease build-up on inside

surfaces.

This is not a defect. The nish on the lid and hood is

porcelain, and will not peel. The peeling is caused by

hardened grease, which dries into paint-like shards,

that will ake o. Regular cleaning will prevent this. See

cleaning instrucons.

Burner output on

“high” seng is

too low. (Rumbling

noise and uering

blue ame at burner

surface.)

Lack of gas.

Supply hose is pinched.

Dirty or clogged orice.

Spider webs or other maer in

venturi tube.

Cracked ceramic le.

Check gas level in propane cylinder.

Reposion supply hose as necessary.

Clean burner orice.

Clean out venturi tube.

Order replacement burner from your Authorized

Napoleon dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Napoleon BISB 245 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info