Bedienungsanleitung Napoleon MIRAGE 485 (Seite 12 von 64) (Englisch, Französisch)

637898

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

www.napoleongrills.com

Tube Burner: The burners are made from heavy wall 304 stainless steel, but extreme heat and a corrosive

environment can cause surface corrosion to occur. This can be removed with a brass wire brush.



Spiders and insects are aracted to the smell of propane and natural gas. The burner is equipped with an

insect screen on the air shuer, which reduces the likelihood of insects building nests inside the burner

but does not enrely eliminate the problem. A nest or web can cause the burner to burn with a so yellow

or orange ame or cause a re (ashback) at the air shuer beneath the control panel.

 Remove the screw that aaches the burner to the

back wall. Slide the burner back and upwards to remove. Cleaning: Use a exible venturi tube brush to

clean the inside of the burner. Shake any loose debris from the burner through the gas inlet. Check the

burner ports and valve orices for blockages. Burner ports can close over me due to cooking debris and

corrosion, use an opened paperclip or the supplied port maintenance bit to clean them. Drill out blocked

ports using this drill bit in a small cordless drill. The ports are easier to clean if the burner is removed from

the grill, but it can also be done with the burner installed. Do not ex the drill bit when drilling the ports,

as this will cause the drill bit to break. This drill is for burner ports only, not for the brass orices (jets)

which regulate the ow into the burner. Take care not to enlarge the holes. Ensure the insect screen is

clean, ght, and free of any lint or other debris.

 Reverse the procedure to reinstall the burner. Check that the valve enters the burner when

installing.

: The grids and warming rack are best cleaned with a brass wire brush during the

pre-heang period. Steel wool can be used for stubborn stains. It is normal that stainless grids (if equipped)

will discolor permanently from regular usage due to the high temperature of the cooking surface.

: The control panel text is printed directly on the stainless steel and with proper

maintenance will remain dark and legible. To clean the panel, use only warm soapy water or stainless steel

cleaner available from your Napoleon dealer. Never apply abrasive cleaners on any stainless surfaces,

especially the printed poron of the control panel or the prinng will gradually rub o.

: Remove the cooking grids. Use a brass wire brush to clean loose debris from

the casng sides and underneath the lid. Scrape the sear plates with a puy knife or scraper, and use a

wire brush to remove the ash. Remove the sear plates and brush debris from the burners with the brass

wire brush. Sweep all debris from inside the gas grill into the drip pan.

WARNING!

Drip Pan: Clean the drip pan frequently (every 4 – 5 uses or as often as required) to avoid grease buildup.

Grease and excess drippings pass through to the drip pan, located beneath the gas grill and accumulate

in the disposable grease tray below the drip pan. To access the disposable grease tray or to clean the drip

pan, slide the drip pan free of the grill. Never line the drip pan with aluminum foil, sand or any other material

as this could prevent the grease from owing properly. The pan should be scraped out with a putty knife or

scraper. Replace the disposable grease tray every 2 – 4 weeks, depending on gas grill usage. For supplies,

see your Napoleon Gas Grill dealer.

: Do not use abrasive cleaners or steel wool on any painted, porcelain or

stainless steel parts of your Napoleon Grill. Doing so will scratch the nish. Exterior grill surfaces should be

cleaned with warm soapy water while the metal is sll warm to the touch. To clean stainless surfaces, use

a stainless steel or a non-abrasive cleaner. Always wipe in the direcon of the grain. Over me, stainless

steel parts discolor when heated, usually to a golden or brown hue. This discoloraon is normal and does

not aect the performance of the grill. Porcelain enamel components must be handled with addional

care. The baked-on enamel nish is glass-like, and will chip if struck. Touch-up enamel is available from

your Napoleon Grill dealer.

WARNING!





WARNING!







Napoleon MIRAGE 485 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info