Bedienungsanleitung Napoleon Prestige 500 (Seite 6 von 64) (Englisch, Französisch)

637893

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

www.napoleongrills.com

: Ensure the gas regulator hose is kink free. Remove the cap or plug from the cylinder

fuel valve. Insert the black QCC1 regulator nipple onto the QCC1 fuel valve. Hand ghten clockwise. Do not

use tools. Leak test all joints prior to using the grill. A leak test must be performed annually and each me

a cylinder is hooked up or if a part of the gas system is replaced.

If this grill is to be connected directly to a house propane gas supply line, follow the instrucons for the

natural gas hook-up. Oponal side burners must also follow the natural gas hook-up instrucons.

Note: The propane tank heat shield is not required when the grill is connected to a xed fuel supply, as its

sole funcon is to shield the propane tank normally used with the grill. Ensure that the supply pressure is

11 inches water column.

: These connecons must be made by a licensed gas er. This natural gas grill is

supplied with a gas supply hose (complete with a quick disconnect) designed for natural gas and cered

for outdoor use. The gas grill is designed to operate at an inlet pressure of 7 inches water column. Piping

and valves upstream of the quick disconnect are not supplied. The installaon must comply with CAN

B149.1 Natural Gas and Propane installaon code in Canada, or to the Naonal Fuel Gas Code, ANSI

Z223.1 in the United States. The gas supply pipe must be suciently sized to supply the BTU/h specied

on the rang plate, based on the length of the piping run.

The quick disconnect must not be installed in an upward direcon and a readily accessible manual shut-o

valve must be installed upstream of, and as close to, the quick disconnect as is feasible. The ared end of

the hose must be connected to the ng on the end of the manifold tube or ex tube (if applicable) as

illustrated in the Natural Gas Hose Aachment diagram. Tighten using two wrenches. (Do not use thread

sealer/pipe dope.) Leak test all joints prior to using the gas grill.

WARNING!

• The installaon must be performed by a licensed gas er, and all connecons must be leak tested

before operang the grill.

• Do not route hose underneath the drip pan.

• Do not route hose between boom shelf space and back panel.

• Do not route hose over top of rear panel.

• Ensure all hose connecons are ghtened using two wrenches. Do not use Teon tape or pipe

dope on any hose connecon.

• Ensure the hose does not contact any high temperature surfaces or it may melt and leak causing a

re.

• Leak test all the connecons using a soap and water soluon as per the leak tesng instrucons

found in the manual.

• The outdoor cooking gas appliance and its individual shuto valve must be disconnected from the gas

supply piping system during any pressure tesng of that system at test pressures in excess of 0.5 psi

(3.5 kPa).

• The outdoor cooking gas appliance must be isolated from the gas supplypiping system by closing its

individual manual shuto valve during any pressure tesng of the gas supply piping system at test

pressures equal to or less than 1/2 psi (3.5 kPa).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Napoleon Prestige 500 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Napoleon Prestige 500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info