Bedienungsanleitung Napoleon PTSS165 (Seite 10 von 32) (Englisch, Französisch)

637904

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

www.napoleongrills.com

Troubleshoong

Problem Possible Causes Soluon

Low heat / Low ame

when valve turned to

high.

Blockage of gas.

Improper preheang.

Cylinder freezing up.

Check for spider webs in the burner or orice.

Preheat grill with main burners on high for 5 to

10 minutes.

When cooking for long periods of me, or

when the cylinder is close to being empty, or

low outside air temperatures, 1 lb cylinders do

not have enough weed surface area to allow

liquid propane to turn to vapour. Put on a

fresh 1 lb cylinder or hook-up to a 20 lb tank.

Excessive are-ups/

uneven heat.

Sear plates installed incorrectly.

Improper preheang.

Excessive grease and ash build

on sear plates and in drip pan.

Incorrect bole posion.

Ensure sear plate is installed with the holes

towards the right end of the grill.

Preheat grill with both main burners on high

for 5 to10 minutes.

Clean sear plates and drip pan regularly. Do

not line pan with aluminum foil. Refer to

cleaning instrucons.

Ensure bole is in an upright posion when

operang the grill, hanging from the regulator.

Burners burn with

yellow ame,

accompanied by the

smell of gas.

Possible spider web or other

debris, or improper air shuer

adjustment.

Thoroughly clean burner by removing. See

general maintenance instrucons. Open air

shuer slightly according to combuson air

adjustment instrucons. (This must be done

by a qualied gas installer.)

Flames li away from

burner, accompanied

by the smell of

gas, and possibly

dicules in lighng.

Improper air shuer

adjustment.

Close air shuer slightly according to

combuson air adjustment instrucons. (This

must be done by a qualied gas installer.)

Burner will not light

with the igniter,

but will light with a

match.

Loose electrode wire.

Electrode is cracked or broken.

Damaged electrode wire.

Check that electrode wire is rmly pushed

onto the terminal on the back of the igniter.

One spark systems must use a one spark

igniter.

Replace electrode.

Replace electrode wire.

“Paint” appears to be

peeling inside lid or

hood.

Grease build-up on inside

surfaces.

This is not a defect. The lid and hood are

stainless steel, and will not peel. The peeling

is caused by hardened grease, which dries into

paint-like shards that ake o. Regular cleaning

will prevent this. See cleaning instrucons.

Burner output on

“high” seng is

too low. (Rumbling

noise and uering

blue ame at burner

surface.)

Lack of gas.

Supply hose is pinched.

Dirty or clogged orice.

Spider webs or other maer in

venturi tube.

Check gas level in propane cylinder.

Reposion supply hose as necessary.

Clean burner orice.

Clean out venturi tube.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Napoleon PTSS165 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Napoleon PTSS165

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info