Bedienungsanleitung Native Komplete Kontrol S25 MK1 (Seite 146 von 147) (Englisch)

707117

146

Zoom out

Zoom in

Vorherige Seite

1/147

Nächste Seite

• Walls button: Sets the behavior of the ball when it reaches the range limits. If Walls is set to

on, the ball bounces off the range limit and continues its trip in the opposite direction. If Walls is

set to off, the ball jumps to the opposite range limit and continues from there in the same direc-

tion.

Tempo Mode

Just like Ball mode, Tempo mode simulates a ball that is attracted by the gravity of your finger.

The current position of the ball (the parameter value) is indicated by a blue LED. You can play it in

the same way as Ball mode (see above), however in this case the ball adopts its movement to a

steady beat instead of slowing down and stopping. This enables you to create tempo-synced mod-

ulations with the Modulation Strip. When using KOMPLETE KONTROL as a plug-in, the tempo is

defined by the host. When using the KOMPLETE KONTROL stand-alone application, you can set

the tempo in the header of the software interface. In Ball mode, the following additional settings

are available for the Modulation Strip:

• Display menu: Lets you select one of two ways to display the current state of the Modulation

Strip: Bar or Dot. Bar displays a bar of lit LEDs from the default position of the strip to the cur-

rent value; whereas Dot displays a dot of lit LEDs at the current value.

• Rate menu: Lets you select one of 13 beat divisions to set the beat of the ball’s movement rela-

tive to the tempo, from 1/8 to 4/1, including triplet and dotted time signatures.

• Friction slider: Adjusts the rate at which the ball movement catches up with the tempo. The

higher the Friction value, the quicker the ball will match the beat as set in the Rate menu.

When fully right, the ball matches the given beat instantly.

• Gravity slider: Adjusts the attraction of your finger on the ball: The higher the Gravity value,

the faster the ball will move. This parameter doesn’t affect the ball movement if you throw the

ball with your finger (see above).

• Walls button: Sets the behavior of the ball when it reaches the range limits. If Walls is set to

on, the ball bounces off the range limit and continues its trip in the opposite direction. If Walls is

set to off, the ball jumps to the opposite range limit and continues from there in the same direc-

tion.

Stepped Mode

This mode divides the Modulation Strip into two to five sections, indicated by white LEDs. When

being pressed with a finger, each section triggers one of two to five evenly spaced parameter val-

ues across the whole modulation range. The currently active section (parameter value) is indicated

by three blue LEDs. In Stepped mode, the following additional settings are available for the Modu-

lation Strip:

• Divisions menu: Lets you select the number of sections the Modulation Strip is divided into.

17.3.2. Selecting and Editing a Modulation Strip Mode

In the KOMPLETE KONTROL software, you can select a mode for Modulation Strip and edit its

parameters by performing the following procedure:

1. Go to the Modulation page of the Touch Strip settings.

Configuring Touch Strips

140

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Native Komplete Kontrol S25 MK1 Seite 146

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Native Komplete Kontrol S25 MK1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info