Bedienungsanleitung Nautilus E614 (Seite 41 von 44) (Englisch)

671408

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Condition/Problem Things to Check Solution

Check data cable

connections/orientation

Be sure cable is connected securely and oriented properly.

Small latch on connector should line up and snap into place.

Reset machine Unplug unit from electrical outlet for 3 minutes. Reconnect to

outlet.

Check magnet position

(requires shroud removal)

Magnet should be in place on pulley.

Check Speed Sensor

(requires shroud removal)

Speed sensor should be aligned with magnet and connected to

data cable. Realign sensor if necessary. Replace if there is any

damage to the sensor or the connecting wire.

Fan will not turn on or will

not turn off

Check data cable integrity All wires in cable should be intact. If any are cut or crimped,

replace cable.

Check data cable

connections/orientation

Be sure cable is connected securely and oriented properly.

Small latch on connector should line up and snap into place.

Reset machine Unplug unit from electrical outlet for 3 minutes. Reconnect to

outlet.

Fan will not turn on, but

Console operates

Check for blockage of fan Unplugunitfromelectricaloutletfor5minutes.Removemate-

rial from fan. If necessary, detach the Console to help with

removal. Replace the Console if unable to remove blockage.

Unit rocks/does not sit

level

Check leveler adjustment Adjust levelers until machine is level.

Check surface under unit Adjustmentmaynotbeabletocompensateforextremelyun-

even surfaces. Move machine to level area.

Foot pedals loose/unit

difculttooperate

Hardware Tightly secure all hardware on the Pedal Arms and Handlebar

Arms.

Drive train click/tick

noise once per full crank

revolution

Check crank/pulley

assembly

Disconnect left and right foot assemblies and rotate crank. If

sound persists, replace crank/pulley assembly. If sound does

not come from rotating crank, check foot assemblies and up-

per/lower handlebars.

Check foot assemblies,

leg assemblies, handlebar

assemblies

Manually move foot, leg, and handlebar assemblies to isolate

sound. Replace part making sound.

Squeaking noise

that appears a few

minutes into a workout

and normally will get

progressively worse as

the workout continues

Bolt that connects the

swingarmstotheaxle

running through the

console mast

Loosen pivot rod bolt slightly until noise goes away. See video

for demonstration. White lithium grease can also be applied for

atemporaryx.ContactCustomerCareforassistance.

Roller squeaking on rail Apply silicone lubricant to a dry cloth and wipe the rails to

eliminate roller noise.

Incline assembly sticks/

difculttoadjust

Check position of incline

assembly

Adjust levelers to raise the front of rail assembly until there

is0.6cm-1.25cm(1/4”-1/2”)spacebetweenthetopofthe

incline assembly and the main unit shroud.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nautilus E614 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info