Bedienungsanleitung Nautilus R614 (Seite 32 von 42) (Englisch)

671427

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

Heart Rate Control (HRC) Workout Programs

The Heart Rate Control (HRC) programs let you set a heart rate goal for your workout. The program monitors your heart

rate in beats per minute (BPM) from the Contact Heart Rate (CHR) sensors on the machine or from a Heart Rate Monitor

(HRM) chest strap, and adjusts the workout to keep your heart rate in the selected zone.

Note: The console must be able to read the heart rate information from the CHR sensors or HRM for the HRC program

to work correctly.

The Target Heart Rate programs use your age and other User information to set the Heart Rate Zone values for your

workout.Theconsoledisplaythengivespromptsforyoutosetupyourworkout:

1. SelecttheHeartRateControlworkoutlevel:BEGINNER( “BEG” ) orADVANCED(“ADV”)andpushOK.

2. Push the Increase() or Decrease() buttons to selectthepercentageofmaximumheartrate:50–60%,60–70%,

70–80%,80–90%.

Consultaphysicianbeforeyoustartanexerciseprogram.Stopexercisingifyoufeelpainortightnessinyourchest,

become short of breath, or feel faint. Contact your doctor before you use the machine again. Use the values calcu-

lated or measured by the machine’s computer for reference purposes only. The heart rate displayed on the console

isanapproximationandshouldbeusedforreferenceonly.

3. Push the Increase() or Decrease() buttons to select the Goal type, and push OK.

4. Push the Increase() or Decrease() buttons to set the goal value for the workout.

Note: Be sure to allow time for your heart rate to reach the desired heart rate zone when setting the goal.

5. PushOKtostarttheworkout.

Changing a Workout Program During a Workout

The Console allows a different Workout Program to be started from an active workout.

1. From an active workout, push PROGRAMS.

2. Push the Increase() or Decrease() buttons to select the desired workout program, and push OK.

3. Push the Increase() or Decrease() buttons to select the Goal type, and push OK.

4. Push the Increase() or Decrease() buttons to set the value for the workout.

5. PushOKtostoptheactiveworkoutandstartthenewworkout.

ThepreviousworkoutvaluesaresavedtotheUserProle.

Pausing or Stopping

The Console will go into Pause Mode if the user stops pedaling and pushes PAUSE/END during a workout, or there is no

RPMsignalfor5seconds(usernotpedaling).TheConsolewillcyclethroughaseriesofmessagesthatchangeevery4

seconds:

- WORKOUT PAUSED

- PEDAL TO CONTINUE (if a bike) / STRIDE TO CONTINUE (if an elliptical)

- PUSH END TO STOP

During a paused workout, you can use the Increase/Decrease buttons to move through the result channels manually.

1. Stop pedaling and push the PAUSE/END button to pause your workout.

2. To continue your workout, push OK or start pedaling.

To stop the workout, push the PAUSE/END button. The Console will go into Results / Cool Down mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nautilus R614 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info