Bedienungsanleitung Nautilus T684 (Seite 44 von 50) (Englisch)

737242

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

Lubricating the Walking Belt

Your treadmill is equipped with a low maintenance deck and belt system. Belt friction can affect the function and life of the

machine. Lubricate the belt every 3 months or every 25 hours of use, whichever comes ﬁrst. Even if the treadmill is not in use,

silicone will dissipate and the belt will dry out. For the best results lubricate the deck periodically with the silicone lubricant

supplied with the machine, using the following instructions:

1. Turn off the power to the machine with the power switch.

2. Unplug the treadmill fully from the wall outlet, and remove the power cord from the machine.

To reduce the risk of electrical shock, always unplug the power cord and wait 5 minutes before cleaning,

maintaining or repairing this machine. Place the power cord in a secure location.

Note: Make sure the treadmill is located on a surface that is easy to clean.

3. Fold the treadmill. Refer to the “Moving the Machine” procedure in this manual. Be sure that the hydraulic lift is correctly

locked in place

Use proper safety precautions and lifting techniques. Use a second person if necessary.

Do not use the walking belt or rear roller to lift the treadmill. These parts do not lock in place and can abruptly move.

Injury to you or damage to the machine can occur.

4. Make sure that the locking mechanism is engaged. Carefully pull back on the walking deck and make sure that it does

not move. When you do this, keep clear of movement path in case the treadmill lock is not engaged.

Do not lean against the treadmill when it is folded. Do not put items on it that could cause it to become unstable or fall.

Do not connect the power cord or try to operate the treadmill in the folded position.

5. Apply a few drops of the lubricant to the inner surface of the belt for the entire width of the belt. A very thin layer of sili-

cone lubricant on the entire deck below the belt is desired.

NOTICE: Always use a silicone-based lubricant such as the lubricant supplied with the machine. Do not use a degreaser like

WD-40

as this could seriously impact performance. We can recommend that you use the following:

• 8300 Silicone Spray, available at most Hardware and Auto Parts stores.

• Lube-N-Walk

Treadmill Lubrication Kit, available from your local distributor or your local specialty ﬁtness dealer.

6. Manually rotate the belt 1/2 of the length of the belt and apply lubricant again.

7. Unfold the machine. Refer to the “Unfolding the Machine” procedure in this manual.

Keep clear of the movement path of the walking deck. Hold onto the walking deck until approximately 2/3 of the

movement down. The walking deck can possibly drop quickly in the last part of the movement.

If you used spray lubricant, wait 5 minutes before turning on power to the machine to allow the aerosol to dissipate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nautilus T684 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info