Bedienungsanleitung Nautilus U626 (Seite 34 von 36) (Englisch)

736334

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Condition/Problem Things to Check Solution

Resistance does not

change(machineturnson

andoperates)

Batteries(ifequipped) Replace batteries and check for proper operation.

Check Console Check for visual sign that Console is damaged. Replace Con-

sole if damaged.

Check data cable integrity All wires in cable should be intact. If any are visibly crimped or

cut, replace cable.

Check data cable

connections/orientation

Be sure cable is connected securely and oriented properly.

Reseat all connections. Small latch on connector should line up

and snap into place.

Check Servo Motor

(requiresshroudremoval)

If magnets move, adjust until they are within the proper range.

Replace Servo Motor if not functioning properly.

If the above steps do not resolve the problem, contact your lo-

cal distributor for further assistance.

Consoleshutsoff(enters

sleepmode)whileinuse

Checkelectrical(wall)

outlet

Make sure unit is plugged into a functioning wall outlet.

Check connection at front

of unit

Connection should be secure and undamaged. Replace

adapter or connection at unit if either are damaged.

Check data cable integrity All wires in the cable should be intact. If any are cut or crimped,

replace cable.

Check data cable

connections/orientation

Be sure cable is connected securely and oriented properly.

Small latch on connector should line up and snap into place.

Reset Machine Unplug unit from electrical outlet for 3 minutes. Reconnect to

outlet.

Check magnet position

(requiresshroudremoval)

Magnets should be in place on pulley.

Check Speed Sensor

(requiresshroudremoval)

Speed sensor should be aligned with magnets and connected

to data cable. Realign sensor if necessary. Replace if there is

any damage to the sensor or the connecting wire.

Fan will not turn on or will

not turn off

Check data cable integrity All wires in cable should be intact. If any are cut or crimped,

replace cable.

Check data cable

connections/orientation

Be sure cable is connected securely and oriented properly.

Small latch on connector should line up and snap into place.

Reset machine Unplug unit from electrical outlet for 3 minutes. Reconnect to

outlet.

Fan will not turn on, but

Console operates

Check for blockage of fan Unplugunitfromelectricaloutletfor5minutes.Removemate-

rial from fan. If necessary, detach the Console to help with

removal. Replace the Console if unable to remove blockage.

Unit rocks/does not sit

level

Check leveler adjustment Adjust levelers until bike is level.

Check surface under unit Adjustmentmaynotbeabletocompensateforextremelyun-

even surfaces. Move bike to level area.

Pedalsloose/unitdifcult

to pedal

Check pedal to crank arm

connection

Pedal should be tightened securely to crank. Insure connection

is not cross-threaded.

Checkcrankarmtoaxle

connection

Crankshouldbetightenedsecurelytoaxle.Besurecranksare

connected at 180 degrees from each other.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nautilus U626 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nautilus U626

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info