Bedienungsanleitung Navman Depth 3100 (Seite 9 von 13) (Englisch)

512542

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

DEPTH 3100 Installation and Operation Manual

NAVMAN

Correct installation is critical to the performance of

the unit. It is vital to read this section of the manual

and the documentation that comes with the other

parts before starting installation.

The DEPTH 3100 can:

Drive external beepers or lights for the alarm.

Send and receive data from other NAVMAN

instruments connected via NavBus. Settings

for alarms, units, calibration and backlighting

are shared (see section 4-1).

Send and receive NMEA data from other

instruments (see section 4-2).

Warnings

The unit is waterproof from the front. Protect the rear

of the unit from water, or else water might enter the

breathing hole and damage the unit. The warranty

does not cover damage caused by moisture or water

entering the back of the unit.

Ensure that any holes that you cut will not weaken

the boat’s structure. If in doubt, consult a qualified

boat builder.

6-1 Installation

DEPTH 3100 display unit

1 Choose a location for the display unit that is:

Easily seen and protected from damage.

At least 100 mm (4") from a compass and

at least 500 mm (1.65 ft) from a radio or

radar antenna.

Away from engines, fluorescent lights, and

power inverters.

Accessable from behind; the minimum

clearance required at the back is 50 mm

(2") (see mounting diagram).

With the back of the unit protected from

moisture.

6 Installation and setup

2 The unit must mount on a flat panel which is

less than 20 mm (0.75") thick. Stick the

mounting template in place. Drill a 50 mm (2")

fixing hole through the centre hole in the

template. Note that the template allows space

around the unit for the protective cover.

3 Remove the fixing nut from the back of the unit.

Insert the stud at the back of the unit through

the mounting hole. Hand tighten the fixing nut.

Transducers

1 If the DEPTH 3100 does not come with a

transducer, choose a suitable transducer (see

section 5-3). If the DEPTH 3100 is supplied

with a transducer, see section 5-3 to ensure

that it is suitable.

2 Choose a suitable location for the transducer

and install it by following the instructions in the

Transducer Installation manual.

3 Fit the cables between the transducer and the

display unit:

Keep the cable away from other cables,

engines, fluorescent lights, power inverters

and radio or radar transmitters.

Ensure no connectors lay in the bilge.

If necessary, extend the cable by adding

extension cables.

Do not cut the cable on any depth

transducer.

Secure the cable at regular intervals.

4 Connect the transducer to the display unit

connector.

The choice, location, angle and installation of

the transducers is the most critical part of the

installation. If they are not correct, the unit can

not perform at its designed potential. If in

doubt, consult your NAVMAN dealer. Plastic

through hull transducers are usually unsuitable

for wood hulls. If in doubt, consult a marine

surveyor or marine engineer.

Clearance

50 mm (2") minimum

20 mm (0.75")

maximum thickness

Fixing nut

Display

unit

Fixing hole

50 mm (2")

Side view of display unit mounting

Cables

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Depth 3100 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Depth 3100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info