Bedienungsanleitung Navman Diesel 3200 (Seite 20 von 77) (Englisch)

512555

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

FUEL 3100 / DIESEL 3200 Installation and Operation Manual

NAVMAN

To check out the installation:

1 Power on the boat and any other

instruments. Check the instruments work

properly.

2 Enter the setup data (see section 3).

Set dUAL, motor , and InPUt first, then

enter the rest of the setup data.

For boats with twin tanks or twin engines,

remember to enter port and starboard data

separately where required.

3 Fill the fuel tank(s) and set the fuel in the

tank(s) in the FUEL 3100 or DIESEL 3200 (see

section 5).

4 On boats with twin engines, check the

installation of the port and starboard fuel

sensors:

• DIESEL 3200: Start the port engine. Check

the LED lights under the sensors are

blinking. This indicates the sensors are

operating correctly. Confirm the fuel flow is

being displayed as port engine fuel usage

on the instrument. (If it is being displayed

as starboard engine fuel usage, swap

over the fuel flow sensor connectors on

the ‘T’ connector.) Repeat the check with

starboard engine.

• FUEL 3100: Start the port engine. Confirm

the fuel flow is being displayed as port

engine fuel usage on the instrument. If it is

being displayed as starboard engine fuel

usage, reconfigure the settings (see section

3-3).

5 FUEL 3100 only: Calibrate the fuel sensor(s)

(see section 3-4).

6 If a paddlewheel speed sensor is

connected, calibrate it (see sections 3-8

and 3-9).

7 Take the boat for a trial run and check the

unit is displaying the correct data.

FUEL 3100: Recalibrate the FUEL 3100’s fuel

sensor(s) after the first 100 engine hours (see

section 3-4).

When you add or remove fuel from a tank, you

must enter into the FUEL 3100 or DIESEL 3200

how much fuel you have added or removed.

Otherwise REMAINING, RANGE and the low

fuel alarm will be meaningless. Twin tanks

connected by an open balance pipe should be

trated as a single fuel tank.

When you add or remove fuel from a tank:

a When you fill a tank

1 Fill the tank.

2 Press until REMAINING is displayed.

3 If the boat has twin tanks, press ENT until

the display shows the name of the tank you

have filled, PORT or STBD.

4 Press and together.

5 If the boat has twin tanks and you are filling

the other tank as well, repeat the above

steps.

Note:

It is often very difficult to refill underfloor

fuel tanks to the same level twice, due to air

pockets. Because of this, owners of boats with

underfloor fuel tanks should:

• Ensure the boat is trimmed to sit at

the same angle in the water each time

procedure a above is followed.

• Mostly use procedure b below when filling

the tank, but use procedure a above about

every tenth fill.

b When you fill or part fill a tank

1 Before adding or removing fuel, press ESC

and ENT together, then press until the

FUEL setup menu is displayed.

2 Press ENT, then press or until the

FUEL data is displayed.

5 When you add or remove fuel

4-7 Testing the installation

4-8 Resetting to factory defaults

To reset to factory defaults:

1 Turn the power off.

2 Hold ENT + while turning on the power

and for at least five seconds after.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Diesel 3200 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Diesel 3200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info