Bedienungsanleitung Navman FISH 4100 (Seite 5 von 25) (Englisch)

470017

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

FISH 4100 Installation and Operation Manual NAVMAN

Power and transducer connection

FISH 4100

One end of the integrated transducer / power cable

has an 8 pin LT connector plug. Push this plug into

the socket located on the rear of the display unit,

then turn the collar to lock. Make sure that the collar

is secure for a watertight connection.

FISH 4150

One end of the power cable has a black 8 pin LT

connector plug. Push this plug into the lower socket,

which has a black nut and is located on the rear of

the display unit, then turn the collar to lock. Make

sure that the collar is secure for a watertight

connection.

One end of the transducer cable has a blue 8 pin LT

connector plug. Push this plug into the upper socket,

which has a blue nut and is located on the rear of

the display unit, then turn the collar to lock. Make

sure that the collar is secure for a watertight

connection.

If the transducer is not connected, the message

“NO TRANSDUCER DETECTED. ENTER

SIMULATION MODE?” will appear. Press

switch between YES or NO. (More information on

the simulation mode can be found in the following

section). Press

to confirm the selection and

the startup sequence will continue. (Note: If the

transducer was not intentionally disconnected,

turn the display unit off and refer to the section on

Troubleshooting in Appendix B, 9.)

Names of keys:

Cursor key

key

Gain key

Power

Definition of Press and Hold in this manual:

· Press means to push the key for less than one

second.

· Hold means to push and hold the key down for

more than one second.

Power on

To turn the fishfinder on press .

Note: if the ignition wire is connected (see section

5-4) then the fishfinder will turn on automatically

when the boat's ignition is turned on.

A title screen briefly appears which displays basic

product information, including the software version.

The NAVMAN fishfinder then automatically displays

the screen that was last used.

Power off

To turn the fishfinder off, hold . A countdown box

appears. Continue to hold

for 3 seconds until the

fishfinder turns off.

Note: if the unit is wired for Auto Power (see

section 5-4) the fishfinder can only be turned off

when the boat’s ignition is turned off.

Language selection

To check which language is currently selected, press

to display the MAIN MENU.

Follow these steps to change the language:

1. Power off the unit.

2. While the unit is off, hold down the

key.

3. Keep holding down the key and power on

the unit.

4. The screen displays a list of languages.

Press the Cursor or key to highlight a

language, then press the Cursor key to

select it. The fishfinder will continue the

startup sequence.

For further information, (see section 4-7).

Backlighting

Use the button to adjust the backlighting to suit

individual preferences.

Press

once, at any time, to see the backlight bar.

This is displayed at the bottom of the screen and

shows the current setting.

Press

repeatedly until the desired backlighting

level is achieved. The backlight bar will disappear 2

seconds after the last press.

2 Getting started

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman FISH 4100 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman FISH 4100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info