Bedienungsanleitung Navman FISH 4200 (Seite 23 von 32) (Englisch)

470014

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

23FISH 4200 Installation and Operation Manual

NAVMAN

Correct installation is critical to the performance of

the FISH 4200. There are two components to install,

the display unit and the transducer. It is vital to read

5 Installation

the entire installation section of this manual and

the documentation that comes with the transducer

before attempting installation.

5-1 What comes with the FISH 4200?

Optional transducers

· Through hull Speed/Temperature transducer

· Through hull Depth transducer

· In hull Depth transducer

Other options and accessories

· Replacement paddle wheel

· Adapter cable for through hull transducer

· Carry bag

· Transducer extension cable

· Fuel kit (single or twin available)

Standard configuration

· FISH 4200 display unit

· Power cable

· Mounting bracket (screws included)

· Warranty registration card

· This manual

· Transducer (includes cable kit and screws)

· Transducer Installation Manual

· Screws

· Sun cover

· Flush mounting kit

5-2 Options and Accessories

There are two mounting arrangements:

· Flush mounting requires a solid panel

with access behind for wiring and mounting

screws.

· Bracket mounting requires a panel for

mounting the bracket. The bracket can be

rotated and tilted.

Select a position where the display head will be:

· at least 4" (100 mm) away from the compass.

· at least 12" (300 mm) away from any radio

transmitter.

· at least 4' (1.2 m) away from any antenna.

· easy to read by the helmsman and crew

while underway.

· protected from physical damage during

rough sea passages.

· easy to access the 12 volt power source.

· convenient to route the transducer cables.

Bracket mounting

1. Fix the mounting bracket onto the boat using the

three stainless steel screws. Do not overtighten

as the bracket may not rotate.

2. Push the display unit onto the mounting

5-3 Mounting the FISH 4200 Display Unit

bracket and tighten it firmly using the knob on

the mounting bracket.

3. Attach the cables

Removing the FISH 4200

The FISH 4200 can be removed after each use for

protection against the environment or security

reasons.

When removing the FISH 4200 ensure that the plugs

left in the boat are not exposed to the elements. Push

the attached dust covers over the exposed ends of

the plugs. Keep the display unit in a dry clean place

such as the optional NAVMAN carry bag.

Flush mounting

1. Cut a hole in the bulkhead for the display

unit using the flush mount template.

2. Drill four holes for the mounting studs

using the flush mount template.

3. Screw the four studs into the brass inserts

in the back of the display unit.

4. Sit the display unit in place and fit the

washers and nuts to the studs.

Depth Repeater

Repeater for Depth, Speed, Water Temperature,

Battery Voltage (see section 5-5).

Please consult your NAVMAN dealer for more

information.

Power cable

Mounting

bracket

Transducer

Unit

Screws

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman FISH 4200 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info