Bedienungsanleitung Navman FISH 4431 (Seite 6 von 30) (Englisch)

470011

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Fish 4430/4431 Installation and Operation Manual

2 Getting started

For deep-sea fishing with the FISH 4430/4431,

a rapid change in temperature may indicate

the edge of a warm or cold current. The

temperature difference can form a barrier, and

the fish may not swim through this. Search for

fish on either side of the barrier.

Cleaning and maintenance

The FISH 4430/4431 should be cleaned

with a damp cloth or mild detergent. Avoid

abrasive cleaners and petrol or other solvents.

Always cover or remove a transom-mounted

transducer when repainting the hull. If painting

over a through hull transducer with antifouling

paint then use only one coat of paint. When

repainting the transducer, remove previous

coats of antifouling paint by sanding it lightly.

When not in use, the FISH 4430/4431 can either

be removed from the installation bracket and

stored in a safe, dry, cool place such as the

NAVMAN carry bag, or left on the installation

bracket and securely covered with the optional

sun cover.

Power and transducer connection

FISH 4430

One end of the integrated transducer/power

cable has an 8 pin LT connector plug. Push this

plug into the socket located on the rear of the

display unit, then turn the collar to lock. Make

sure that the collar is secure for a watertight

connection.

FISH 4431

One end of the power cable has a black 8 pin LT

connector plug. Push this plug into the lower

socket, which has a black nut and is located on

the rear of the display unit, then turn the collar

to lock. Make sure that the collar is secure for a

watertight connection.

One end of the transducer cable has a blue

8 pin LT connector plug. Push this plug into

the upper socket, which has a blue nut and is

located on the rear of the display unit, then

turn the collar to lock. Make sure that the collar

is secure for a watertight connection.

If the transducer is not connected, the

message “NO TRANSDUCER DETECTED. ENTER

SIMULATION MODE?” will appear. Press

to switch between YES, NEVER or NO. (More

information on the simulation mode can be

found in the following section). Press to

confirm the selection and the startup sequence

will continue.

(Note: If the transducer was not intentionally dis-

connected, turn the display unit off and refer to the

section on Troubleshooting in Appendix B.)

Names of keys:

Cursor key

key

+ gain key

- gain key

Power key

Definition of Press and Hold in this manual:

· Press means to push the key for less than

one second.

· Hold means to push and hold the key down

for more than one second.

Power on

To turn the fishfinder on press .

Note: if the unit is wired for Auto Power (see sec-

tion 5-4) the fishfinder will turn on automatically

when the boat’s ignition is turned on.

A title screen briefly appears which displays

basic product information, including the

software version.

The FISH 4430/4431 then automatically displays

the screen that was last used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman FISH 4431 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman FISH 4431

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info