Bedienungsanleitung Navman FISH 4500 (Seite 27 von 36) (Englisch)

470004

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Correct installation is critical to the performance

of the FISH 4500/4600. There are two compo-

nents to install, the display unit and the trans-

6 Installation and Maintenance

ducer. It is vital to read the entire installation

section of this manual before attempting to

install the components.

6-1 What comes with this product?

Standard configuration:

• FISH 4500/4600 display unit

• Power cable

• Mounting bracket (screws included)

• Warranty registration card

• This manual

• Sun cover for display unit

• Flush mounting kit

• Dual frequency transom transducer (includes

cable kit and screws)

• Transom Mount Transducer Installation Manual.

6-3 Mounting and removing the display unit

• TRACKER series of chartplotters

• Through hull dual frequency transducer

• Through hull speed/temperature transducer

• Fuel flow kit (single or twin engine)

• Replacement paddle wheel

• SmartCraft Gateway

• REPEAT 3100 (see section 6-6 Systems of

several instruments).

• Diesel 3200 for fuel flow on diesel engines

There are two mounting arrangements:

• Flush mounting requires a solid panel with

access behind for wiring and mounting screws.

After flush mounting, the FISH 4500/4600

cannot be tilted or moved after installation

to reduce any unwanted glare or reflections.

Carefully select the best viewing position before

installation. This would generally be in a shaded

area.

• Bracket mounting requires a panel for mount-

ing the bracket. Ensure that the panel is not

likely to deform and is not subject to excessive

vibration. The bracket can be tilted and rotated

so the FISH 4500/4600 can be removed after

each use.

Select a position where the display unit will be:

• At least 4” (100 mm) away from the com-

pass.

• At least 12” (300 mm) away from any radio

transmitter.

• At least 4 ft. (1.2 m) away from any antenna.

• Easy to read by the helmsman and crew

TRACKER

5500/5600 chartplotter

Fuel flow kit

6-2 Options and Accessories

while underway.

• Protected from physical damage during

rough sea passages.

• Easy to access the 12 / 24 V DC power source.

• Convenient to route the transducer cables.

Flush Mounting

1. Cut a hole in the bulkhead for the display unit

using the flush mount template.

2. Drill four holes for the mounting studs using

the flush mount template.

3. Screw the four studs into the brass inserts in

the back of the display unit.

4. Sit the display unit in place and fit the

washers and nuts to the studs.

Bracket Mounting

1. Fix the mounting bracket onto the boat using the

three stainless steel screws. Do not overtighten the

screws, as the bracket may not rotate.

2. Push the display unit onto the mounting

bracket and tighten it firmly using the knob on

the mounting bracket.

3. Attach the cables.

Display unit

Screws

Power cable

Mounting bracket

Dual frequency

transom transducer

Please consult your Navman dealer for more

information.

FISH 4500/4600 Installation and Operation Manual 27

NAVMAN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman FISH 4500 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman FISH 4500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info