Bedienungsanleitung Navman FISH 4600 (Seite 13 von 36) (Englisch)

470005

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

3-7 Setup > Comms

Use this feature when the FISH 4500/4600 is

connected to other Navman instruments through

NavBus or any compatible NMEA instrument.

Press MENU once or more until the Setup menu

is displayed, then select Comms:

NMEA Out

NMEA is generally used with third party instru-

ments. Select to transmit NMEA sentences (see

Appendix A - Specifications).

NMEA data

Use this to specify which NMEA sentences will

be transmitted (see Appendix A - Specifications

and section 5-7 Data display, for information

about how to display NMEA data).

NavBus

NavBus is the preferred method for connecting

the FISH 4500/4600 to other Navman instru-

ments. Select if the instruments are connected

using NavBus.

NavBus Group

Use this when a group of Navman instruments

are connected together using NavBus, to specify

a group of instruments for backlighting, if required.

Then, if the backlight setting on one instrument

in the group is adjusted, the other instruments

change automatically. Otherwise, select 0.

3-8 Setup > Calibrate

Press MENU once or more until the Setup menu

is displayed, then select Calibrate:

The fuel options can

be calibrated only

when the optional sin-

gle or twin engine kit

is installed on petrol/

gasoline engines.

Speed

Calibration may be required because different hull

shapes have different flow characteristics.

Obtain an accurate measurement of the boat’s

speed from a GPS receiver; or by following another

boat travelling at a known speed; or by making a

timed run over a known distance.

Note: for accurate calibration:

• The speed from a GPS receiver should be

greater than 5 knots.

• The speed from another paddlewheel trans-

ducer should be between 5 and 20 knots.

• Best results are achieved in calm conditions

where there is minimal current (best at high or low

tide).

Use the cursor keys to display the speed readout

box, then increase or decrease the readout to

match the independent speed value.

Speed Filter

Increase this setting to stabilise an erratic speed

reading. Decrease to improve reading respon-

siveness. The speed filter can be set from 0 to

30 seconds.

Temperature

The factory settings should be sufficiently accurate

for normal usage. To calibrate the temperature

readout, first measure the water temperature with a

thermometer known to be accurate.

Use the cursor keys

to display the temperature

readout box,

then increase or decrease the value

to match the measured temperature. The tempera-

ture can be set from 32° to 99.9°F (0° to 37.7°C)

with a resolution of 0.1° unit.

To change the units between °F (Fahrenheit) or °C

(Celsius), see section 3-6 Setup > Units.

Temp filter

Increase this setting to stabilise an erratic tem-

perature reading. Decrease to improve reading

responsiveness. The temperature filter can be

set from 0 to 30 seconds.

FISH 4500/4600 Installation and Operation Manual 13

NAVMAN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman FISH 4600 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman FISH 4600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info