Bedienungsanleitung Navman G-PILOT 3380 (Seite 7 von 32) (Englisch)

663849

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

8 NAVMAN G-PILOT 3380 System Installation Manual

The recommended installation sequence is:

1 Read this manual and the documentation

that comes with the other parts.

2 Plan the installation: select where the

equipment and wiring will be installed (see

section 3-2).

3 Install the MCU600 (see section 3-3).

4 Install the steering drive and wire the heavy

duty and light duty power supplies

(see section 3-4).

5 Install the rudder feedback unit

(see section 3-5).

6 Install the compass (see section 3-6).

3 Installation

3-1 Installation sequence

Warning: Correct installation is critical to the

performance of the unit. It is vital to read this

manual and the documentation that comes

with the other parts before starting installation.

Warning:

The MCU600 is not waterproof. Mount the

unit in a dry place.

The G-PILOT 3380 system display unit is

waterproof.

The compass, gyro and rudder feedback

unit are completely waterproof.

Warning: Ensure that any holes that you

cut will not weaken the boat’s structure. If in

doubt, consult a qualified boat builder.

7 Install the gyro (see section 3-7).

8 Install the display unit and any other

marine instruments that will be used with

the G-PILOT 3380 system (see section 3-8).

9 Carry out the dockside setup

(see section 4).

10 Carry out the sea trials (see section 5).

If you are unsure where a part should be

installed, mount and wire the part temporarily,

without cutting holes in the boat. After the sea

trials have been completed, install and wire

the part permanently.

Power supply: The G-PILOT 3380 system

requires two power supplies, both nominally

12 V DC:

A heavy duty supply for the steering drive

A light duty supply for the G-PILOT 3380

system electronics and display unit; this

supply also powers any additional display

units and other instruments.

The power supplies require one or two

switches and fuses or circuit breakers (see

section 3-4).

Steering drive: The G-PILOT 3380 system can

power a hydraulic pump, constantly running

pump set, hydraulic linear drive or mechanical

drive rated at 12 V DC and up to 20 A.

Rudder linkage: To link rudder to rudder

feedback unit (see section 3-5).

For wiring, see Select Wire Table in section 3-4-2.

External beepers or lights (optional ):

The external output is switched to ground,

30 V DC and 250 mA maximum. If the beepers

and lights require more than 250 mA total, fit

a relay.

Other marine instruments (optional): Wind,

speed or GPS instruments can be connected

(see section 1-2).

Other parts: For systems of several

instruments, wiring and connectors are

required. Navman junction boxes can simplify

wiring several Navman instruments together

(see section 1-2 or the NavBus Installation and

Operation Manual).

Coupling connectors and 10 m (33 ft)

extension

cables are available to extend the rudder

feedback unit, compass or gyro cables. Do not

fit more than one extension cable to each unit.

For more information, consult your

Navman dealer.

2-2 Other parts required

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman G-PILOT 3380 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman G-PILOT 3380

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info