Bedienungsanleitung Navman Multi 3100 (Seite 6 von 19) (Englisch)

512549

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

NAVMAN

MULTI 3100 Installation and Operation Manual

2-1 Turn on and off

Turn the unit on and off with the auxiliary power switch

on the boat. The unit does not have its own power

switch. When you turn it off, any settings you have

made are retained.

If the word SIM flashes at the bottom, right of the

display, then the unit is in simulate mode (see

section 2-5).

2-2 Basic operation

The keys

The unit has four keys, labelled and .

In this manual:

Press means to push the key for less than one

second.

Hold for two seconds means to hold the key

down for two seconds or more.

Press one key + another key means to push

both keys together.

Set backlight level for screen and keys

You can set the backlight to one of four brightness

levels or off. Press

once to display the current

backlight level, press again to change the level:

Change the items displayed

The display can show two values at once, one in the

top part of the screen and one in the bottom. If an

item displays as dashes (— —) then it means that

the value is outside the range, for example the depth

might be too deep or unknown.

To change what is displayed in the top part of the

screen, press one or more times to select:

Speed.

Avg speed.

Max speed.

Trim speed.

Depth.

Temperature.

To change the value displayed in the bottom part of

the screen, press

one or more times to select:

Speed.

Depth.

Trip log (distance).

Total log (distance).

Battery voltage.

Countdown timer.

2-3 Change units

To change the speed and log units, press

until SPEED is displayed, then hold until the

units change; if necessary, hold again until

the units change again.

To change the depth units, press until

DEPTH is displayed, then hold until the

units change; if necessary, hold until the

units change again.

To change the temperature units, press

until the temperature is displayed, then hold

until the units change.

2-4 Alarms

The MULTI 3100 can be set to sound an alarm when

the water is too deep or too shallow (see sections

5-2 and 5-3). When the alarm sounds, the internal

beeper sounds, the symbol on the display flashes

and any external beepers or lights operate.

Press

to mute the alarm. The alarm stays muted

until the depth becomes returns to the pre-alarm

condition or is within the alarm parameters. The

alarm will sound if the depth becomes too deep or

too shallow again.

2-5 Simulate mode

Simulate mode allows you to become familiar with

the unit off the water. In Simulate mode, the MULTI

3100 functions normally except that the transducers

are ignored and the unit generates this data internally.

The word SIMULATE flashes at the bottom, right

corner of the screen.

To turn Simulate mode on or off:

1 Turn the power off.

2 Hold down while you turn the power on.

2 Operation

Backlight

Level 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Multi 3100 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Multi 3100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info