Bedienungsanleitung Navman Repeat 3100 (Seite 8 von 40) (Englisch)

512548

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

REPEAT 3100 Installation and Operation Manual

NAVMAN

5 Installation and setup

Clearance 50 mm

(2") minimum

20 mm (0.75")

maximum thickness

Fixing nut

Cables

Display

unit

Fixing hole

50 mm (2")

Side view of display unit mounting

5-1 Installation

REPEAT 3100 display unit

1 Choose a location for the display unit that is:

Easily seen and protected from damage.

At least 100 mm (4") from a compass and

at least 500 mm (1.65 ft) from a radio or

radar antenna.

Away from engines, fluorescent lights, and

power inverters.

Accessible from behind; the minimum

clearance required at the back is 50 mm

(2") (see right).

With the back of the unit protected from

moisture.

2 The unit must mount on a flat panel which is

less than 20 mm (0.75") thick. Stick the

mounting template in place. Drill a 50 mm (2")

fixing hole through the centre hole in the

template.

Note that the template allows space around

the unit for the protective cover.

3 Remove the fixing nut from the back of the unit.

Insert the stud at the back of the unit through

the mounting hole. Hand tighten the fixing nut.

Power/data cable wiring

Follow the wiring example on the next page:

1 The REPEAT 3100 requires 12 V DC power.

Fit a power switch and fuse to the power

supply or power the unit from a fused auxiliary

switch. The fuse should be 1 A for up to five

NAVMAN 3100 series instruments.

2 If the REPEAT 3100 is to receive data from

other instruments via the NavBus, install these

instruments and connect the REPEAT 3100 to

the NavBus.

Note: If an instrument can be connected to the

REPEAT 3100 by both NavBus and by NMEA,

then use the NavBus, because more

information can be shared via the NavBus (see

section 3-1).

Correct installation is critical to the performance of

the unit. It is vital to read this section of the manual

and the documentation that comes with the other

parts before starting installation.

Warnings

The unit is waterproof from the front. Protect the rear

of the unit from water, or else water might enter the

breathing hole and damage the unit. The warranty

does not cover damage caused by moisture or water

entering the back of the unit.

Ensure that any holes that you cut will not weaken

the boat’s structure. If in doubt, consult a qualified

boat builder.

3 If the REPEAT 3100 is to receive NMEA data

from other compatible instruments, install

these instruments and connect each

instrument’s NMEA output to one of the three

REPEAT 3100 NMEA inputs. Up to three

instruments can be connected.

4 Tape or cover any unused wires or connectors

to protect them from water and keep them from

shorting together.

Setup and test

Set up the unit as described in section 5-3.

Take the boat for a trial run to check that all the

instruments work correctly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Repeat 3100 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Repeat 3100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info