Bedienungsanleitung Navman Speed 3100 (Seite 7 von 17) (Englisch)

512547

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

SPEED 3100 log Installation and Operation Manual

NAVMAN

3 Speed, average speed, maximum speed, trim speed

The unit can display several speeds:

SPEED: The current boat speed.

AVG SPEED: The average speed since AVG

SPEED was reset or the unit was switched on.

MAX SPEED: The maximum speed since MAX

SPEED was reset or the unit was switched on.

TRIM SPEED: Trim speed may be used for

tuning racing boats. Trim speed measures

changes in boat speed, relative to when you

reset trim speed to zero. For example, if the

boat is travelling at 10 knots and you reset trim

speed, then trim speed is zero. Then:

If the boat speed increases to 11.5 knots,

the trim speed is 1.5 knots.

If the boat speed decreases to 8.5 knots,

the trim speed is -1.5 knots.

3-1 Set speed and log units

The speed units can be selected to be KNOTS, KPH

and MPH. Selecting one of these automatically sets

the log distance units to NM, KM or M (miles):

Press or until SPEED is displayed, then

hold until the units change; if necessary,

hold again until the units change again.

3-2 Reset average speed

Resetting starts calculating a new average speed:

1 Press

or until AVG SPEED is displayed.

2 Press

+ .

3-3 Reset maximum speed

Resetting starts calculating a new maximum:

1 Press

or until MAX SPEED is displayed.

2 Press

+ .

3-4 Reset trim speed

Resetting sets the trim speed to zero:

1 Press

until TRIM SPEED is displayed.

2 Press

+ .

3-5 Set speed damping

Waves and wind cause the boat speed to fluctuate

slightly. To give a stable reading, the SPEED 3100

calculates the boat speed and trim speed by

measuring the speed several times and averaging

the measurements. The speed damping value

ranges from 1 to 5:

A lower value averages readings over a shorter

period of time. This gives the most accurate

speed but has the most fluctuations.

A higher value averages readings over a longer

period of time. This gives the most stable speed

but will ignore some true speed changes.

Set the speed damping to the lowest value which

gives a stable speed reading. Values of 1, 2, 3, 4

and 5 average readings over a time period of 6, 12,

18, 24 and 30 seconds respectively. To get the most

accurate, stable trim speeds, you may need to

increase the damping. To set speed damping:

1 Press

+ several times until the Speed

Damping screen is displayed:

2 Press

or to change the damping.

3 Press

3-6 Set speed resolution

This sets how speeds are displayed. It has two

settings:

0.0 Displays speeds as 0.0 to 19.9, 20 up.

0.00 Displays speeds as 0.00 to 19.99, 20.0 to

29.9, 30 up:

To set the speed resolution:

1 Press

+ several times until the Speed

Resolution screen is displayed:

2 Press

or to change the resolution

setting.

3 Press

Damping

equals 4

Value

equals

0.0 or 0.00

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Speed 3100 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Speed 3100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info