Bedienungsanleitung Navman Tracker 5100 (Seite 31 von 42) (Englisch)

512563

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

NAVMAN

Simulate mode is a way of becoming familiar with

the TRACKER (see section 2-6).

Warning: Never have simulate mode on when

the TRACKER is navigating on the water.

Simulate

Turn simulate mode Off or On.

Press MENU and select simulate.

Select On or Off.

Mode

There are two choices for Mode:

Normal

Simulates the boat moving from the selected

start point (see step 1 above) at the given

speed and heading. The options are:

Speed: The simulated boat speed to use.

Heading: The simulated bearing for the

boat to follow.

Tip: To calculate a heading, use the cursor

(see section 3-1-1).

Tip: As the boat moves, vary Heading to

simulate the boat moving off course.

13-10 Simulate setup

Demo

Simulates the boat moving along a route at a

given speed. When it reaches one end it

retraces the route in the other direction. Before

setting this mode enter at least one route (see

section 10-2-1). The options are:

Speed: The simulated boat speed to use.

Route: The route to follow.

To turn simulate mode on from this menu:

1 If turning Normal mode on, go to the chart

display. To start the simulation from the boat

position, press ESC to switch to centre on boat

mode. To start the simulation from a different

point, move the cursor to that point on the

chart.

2 In the Simulate setup menu, select Simulate

and turn it on.

3 Select Mode and set it to Normal or Demo.

4 Select and enter the other data required for

simulate:

Normal requires Speed and Heading.

Demo requires Speed and Route.

14 Systems of several instruments

Several NAVMAN instruments can be connected

together to share data. There are two ways of

connecting instruments together, NavBus or NMEA.

NavBus

NavBus is a NAVMAN proprietary system that allows

systems of multiple instruments to be built using a

single set of transducers. When instruments are

connected by NavBus:

If the units, alarms or calibration are changed

in one instrument, then the values will

automatically change in all other instruments

of the same type.

Each instrument can be assigned to a group of

instruments (see section 13-8). If the backlight

is changed in an instrument in group 1, 2, 3 or

4 then the backlight will automatically change

in the other instruments in the same group.

If the backlight is changed in an instrument in

group 0 then no other instruments are affected.

If an alarm sounds, mute it by clearing the

alarm on any instrument which can display that

alarm.

NavBus and the TRACKER

The TRACKER can display depth data if it is

connected to a depth instrument.

NMEA

NMEA is an industry standard, but is not as flexible

as NavBus as it requires dedicated connections

between instruments. The TRACKER can:

Receive and display depth data.

Receive data from a GPS antenna.

Send GPS position and other navigation data

to an autopilot or other instrument.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Tracker 5100 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Tracker 5100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info