Bedienungsanleitung Navman Tracker 5100 (Seite 34 von 42) (Englisch)

512563

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

NAVMAN

Power/data cable for display unit

Wire the cable as shown on the next page.

Note:

The unit requires 12 V DC power. This power

supply must be protected with a fuse or circuit

breaker of between 2 and 3 A. If it does not

have this, fit a 2 A fuse in the power supply line.

To enable auto power (see section 2-1),

connect the yellow Power/data cable wire to

the positive power supply as shown.

To disable auto power, leave the wire

disconnected; make sure it can not touch any

other conductor.

If the external beepers and lights require more

than 200 mA DC total, fit a relay.

For information on how to connect NavBus, refer

to the NavBus Installation and Operation manual.

Setup and test

1 Remove the dust covers from the connectors.

2 Plug the eight way connectors into their

sockets on the back of the display unit:

Match the colour on the end of the

connector to the colour of the nut on the

socket.

Hold the plug against the socket and rotate

the plug until it slides into the socket.

Lock the plug in place by pushing the

locking collar towards the socket and

turning it a quarter turn clockwise.

Nothing will be damaged if a cable is plugged

into the wrong socket by mistake.

3 If the unit has an external GPS antenna:

Plug the gold connector into its socket on

the back of the display unit.

Hand tighten the locking collar clockwise -

do not overtighten.

4 If the display unit is bracket mounted:

i Hold the display unit in place on the

mounting bracket shaft, with the rubber

washer clamped between the bracket and

the display unit.

ii Adjust the tilt and rotation of the display unit

for best viewing and hand tighten the knob.

5 Remove the dust cover. Turn the TRACKER on

(see section 2-1).

6 Insert any required C-MAP™ chart card (see

section 1-2).

7 When the TRACKER is turned on for the first

time, the TRACKER displays an installation

menu of setup data:

i Select the language to use.

ii Change the setup data if necessary:

Select the data item to change.

Use the cursor keys to change the data.

Press ENT.

iii When the setup data is correct, press

ESC.

These installation options can be changed

later, through the setup menu (see section 13).

8 At the satellite display, check that it picks up

GPS satellites. Wait for the GPS receiver to

start up and the fix type to change from

‘Acquiring’ to ‘GPS fix’. This should take less

than two minutes (see section 7).

9 If the TRACKER is to send NMEA data to an

autopilot, set this up (see section 13-8).

10 If the TRACKER is part of a NavBus system,

set the backlight group. Otherwise turn NavBus

off (see section 13-8).

11 Go on a test run to check that the navigation

equipment works correctly, particularly when a

radio transmitter or radar is used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Tracker 5100 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Tracker 5100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info