Bedienungsanleitung Navman Tracker 5430 (Seite 37 von 44) (Englisch)

512565

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

TRACKER 5430/5430i Installation and Operation Manual

NAVMAN

• Either Basic wiring: When the main

switch is on, the TRACKER must be

powered on manually with the key. The

engine hours counter and fuel counter

are disabled.

• Or Auto power wiring:

The TRACKER

turns on and off automatically when the

ignition is turned on and off (see section

2-1). The engine hours counter and fuel

counter are enabled. Choose auto power

when the optional fuel kit is fitted.

Note: With auto power, the TRACKER can

not be turned off using the key.

2 Wire any external beepers or lights. If the

current is more than 200 mA, fit a relay.

3 If required, connect to other instruments. If

you use the NMEA input on the cable with

the white connector, use a special fuel cable.

For information on how to connect NavBus,

refer to the

NavBus Installation and

Operation Manual.

Setup and test

1 Remove the dust covers from the connectors.

2 Plug the eight way connectors into their

sockets on the back of the display unit:

Match the colour on the end of the

connector to the colour of the nut on the

socket.

Hold the plug against the socket and

rotate the plug until it slides into the

socket.

Lock the plug in place by pushing the

locking collar towards the socket and

turning it a quarter turn clockwise.

Nothing will be damaged if a cable is

plugged into the wrong socket by mistake.

3 If the unit has an external GPS antenna:

Plug the gold connector into its socket on

the back of the display unit.

Hand tighten the locking collar clockwise

- do not overtighten.

4 If the display unit is bracket mounted:

i Hold the display unit in place on the

mounting bracket shaft.

ii Adjust the tilt and rotation of the display

unit for best viewing and hand tighten

the knob.

5 Remove the dust cover. Turn the TRACKER on

(see section 2-1).

6 Insert any required C-MAP™ chart card (see

section 1-2).

7 When the TRACKER is turned on for the first

time, the TRACKER displays an installation

menu of setup data:

i Select the language to use.

ii Change the setup data if necessary:

Select the data item to change.

Use the cursor keys to change the

data.

Press ENT.

iii When the setup data is correct, press ESC.

These installation options can be changed

later, through the setup menu

(see section 13).

8 At the satellite display, check that it picks

up GPS satellites. Wait for the GPS receiver

to start up and the fix type to change from

‘Acquiring’ to ‘GPS fix’. This should take less

than two minutes (see section 7).

9 If the TRACKER is to send NMEA data to an

autopilot, set this up (see section 13-9).

10 If the TRACKER is part of a NavBus system, set

the backlight group. Otherwise turn NavBus

off (see section 13-9).

11 Go on a test run to check that the navigation

equipment works correctly, particularly when

a radio trans mitter or radar is used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Tracker 5430 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Tracker 5430

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info