Bedienungsanleitung Navman Tracker 5430i (Seite 36 von 44) (Englisch)

512566

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

TRACKER 5430/5430i Installation and Operation Manual

NAVMAN

15-3 Installation

Warning: Ensure that any cut holes will

not weaken the boat. If in doubt, consult a

qualified boat builder or marine engineer.

Display unit

1 Find a suitable location for the display unit:

There are two mounting arrangements:

Flush mounting requires a solid panel

with access behind for wiring and

mounting screws. Do not flush mount a

TRACKER 5430i.

Bracket mounting requires a panel for

mounting the bracket. The bracket can be

rotated and tilted.

Choose a location that is easily seen and

not exposed to the direct sun or water. If

possible, mount the display unit in front of

the navigator or to the left of the navigator

because the LCD display is more readable

from these positions.

Keep the unit away from any source of

electrical signals or noise.

For the TRACKER 5430i, with the internal GPS

antenna:

The display unit must have a good view

of the sky and horizon. The view should

not be blocked by large parts of the

superstructure.

The unit can be under glass, perspex,

fibreglass or fabric, but not under metal

or wood.

Do not mount the unit within 3 m (10

ft) of a radio transmitter antenna or

within 0.5 m (20") of the plane of a radar

antenna.

2 For flush mounting:

i Cut a hole in the bulkhead for the display

unit using the flush mount template.

ii Drill four holes for the mounting studs

using the flush mount template.

iii Screw the four studs into the brass inserts

in the back of the display unit.

iv Sit the display unit in place and fit the

washers and nuts to the studs.

For bracket mounting:

i Hold the bracket in place and mark the

screw holes.

ii Drill the screw holes and screw the

bracket in place with the screws

provided. Do not overtighten the screws

or the display unit might not rotate.

Do not fit the display unit yet.

GPS antenna

Fit and wire any GPS antenna required (see

section 7). Follow the instructions in the manual

supplied with the antenna. Connect the antenna

to the TRACKER:

• TRACKER 5430: The cable on the GPS antenna

supplied has a gold plug. Plug this into the

gold connector on the back of the TRACKER.

• TRACKER 5430i: Normally use the internal

antenna - no other antenna is required.

• For NavBus or NMEA GPS sources, see

section 14 and next page.

Optional fuel kit

1 Fit the optional fuel kit following the

instructions supplied with the kit.

Note: If the NMEA input on the fuel sensor

cable is used, then a NAVMAN special fuel

cable is required (see below).

2 Wire the TRACKER for auto power

(see below).

Installation of a DGPS antenna

In areas where satellite differential(WAAS/

EGNOS) is not available an optional combined

GPS/DGPS antenna may be connected

for enhanced accuracy when in range of

conventional land based differential beacons.

Please contact the nearest NAVMAN dealer for

further information.

Power/data cable

1 Wire the power supply. The unit requires 12 V

DC power. The power must be protected with

a fuse or circuit breaker of between 2 and 3

A. If it does not have this, fit a 2 A fuse in the

power supply line.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Tracker 5430i Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Tracker 5430i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info