Bedienungsanleitung Navman Tracker 5500i (Seite 14 von 42) (Englisch)

512562

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

TRACKER 5100/5100i/5500/5500i Installation and Operation Manual

NAVMAN

3-2 Distance and bearing calculator

The distance and bearing calculator can plot a course

of one or several legs and to show the bearing and length

of each leg, as well as the total distance along the course.

The completed course can be converted into a route.

To use the distance and bearing calculator:

1 Press ESC until the chart display is displayed.

Press MENU and select Distance.

2 Move the cursor to the start of the first leg. It

does not matter if this point is a waypoint or

not. Press ENT.

3 To add a leg to the course, move the cursor to

the end of the leg. It does not matter if this

point is a waypoint or not. The display shows

4 To change the data display:

i Select Data setup.

ii Change a data field:

a Press the cursor keys to highlight the

field.

b Press ENT to display a menu of the

data that can be shown in the field.

c Select the data to show in the field;

select None to leave the field empty.

iii Repeat the above step to set the other data

fields. Press ESC.

Tip: If less than four lines are used, the

numeric data will take up less of the chart area.

5 To turn the compass display off or on:

i Select Compass.

ii Select Off or On.

6 Finally, press ESC to return to the chart display.

3-3 Goto

Goto is a simple way of navigating straight to one

point.

To start the Goto

1 Choose the point to go to:

To go to a waypoint or to any point on the

chart:

i Press ESC until the chart display is

displayed.

ii Move the cursor to the destination.

iii Press MENU and select Goto.

To go to a waypoint from the waypoints

display:

i Press DISP and select Waypoints.

ii Press

or to highlight the

destination waypoint.

iii Press MENU and select Goto.

Warning: Make sure the course does not pass

over land or dangerous waters.

2 The TRACKER starts navigating to the

destination (see section 2-7). The chart shows:

The destination point marked with a circle.

The boat’s plotted course to the

destination.

Two CDI lines, parallel to the boat’s plotted

course (see appendix C, CDI).

To cancel a Goto

1 Press ESC until the chart display is displayed.

2 Press MENU and select Cancel goto.

the bearing and length of the leg, as well as

the total distance along the course. Press ENT.

4 To remove the last leg from the course, press

MENU and select Remove.

5 Repeat the above two steps to enter the whole

course.

6 To save the new course as a route, press

MENU and select Save. This also saves any

new points on the course as new waypoints,

with default names. If necessary, edit the route

later (see section 10-2-2) and edit any new

waypoints later (see section 9-2-3).

7 Finally, press ESC to return to the chart display.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Tracker 5500i Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Tracker 5500i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info