Bedienungsanleitung Navman Tracker 5505 (Seite 31 von 68) (Englisch)

512558

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

TRACKER 5505/5505i/5605 Installation and Operation Manual

NAVMAN

10 Fuel functions and display

The Fuel functions require optional petrol/gasoline, diesel or SmartCraft fuel sensors to be installed

and set up.

Each engine has a flow sensor installed to

measure the engine’s fuel flow.

The TRACKER uses these flows, together with

boat speed and engine RPM if available to

estimate the fuel remaining in the tank(s), fuel

used, range and fuel economy. This data is

displayed on the fuel display (see section 10-2).

You can:

display the fuel used during a trip

(seesection 10-2)

set low fuel alarms (see section 10-4)

make fuel consumption curves - graphs

of fuel consumption and boat speed as a

function of engine RPM - to monitor and

optimise boat performance.

(see section 10-6)

10-2 Fuel display

To go to the Fuel display, press , select

Other, then select Fuel.

The display differs according to the number of

engines and tanks. If engine RPM is available

and if you have made and selected a Fuel

Consumption Curve (see section 10-6), press

to switch between a Summary or a Fuel

curve display.

The Fuel display shows

Speed

To select a boat speed sensor, see section 10-5-1.

RPM (if available)

If engine RPM is not available, the display

shows depth.

Remaining

The fuel remaining in the tank(s) is shown as a

vertical gauge on the right of the display. The

height of the yellow bar(s) show how much fuel

remains in the tank(s). If you have set a low fuel

alarm (see section 10-4), a red bar shows the

level at which the alarm will trigger. If there are

two tanks, the left bar shows the port tank, the

right bar shows the starboard tank.

10-1 What the fuel computer does

Used

The fuel used during a trip. On a multi-engine

boat, the data for the port engine is on the left

of the display.

When you want to start measuring how much

fuel is used, go to the Fuel display and:

In a single engine boat, press and

select Clear used.

In a multi-engine boat, the fuel used by

each engine and the total fuel used are

shown. Press , select Clear used

and select:

Port or Starboard to clear the fuel used

by one engine

Both to clear the total fuel used.

Fuel flow

The fuel flow for the engine(s). On a multi

engine boat, the data for the port engine is on

the left of the display. Use the flows to check

the load of each engine.

CAUTION

DANGER

WARNING

To ensure the fuel data is accurate:

When you add or remove fuel from a

tank, tell the TRACKER (see section 10-3)

If the boat has petrol/gasoline sensors,

calibrate them during installation or if

the fuel readings seem inaccurate (see

section 10-7)

Choose an appropriate type of boat

speed sensor to calculate economy,

range and the fuel consumption curve

(see section 10-5)

If the boat uses a paddlewheel sensor

to measure speed, calibrate it during

installation or if the speed readings

seem inaccurate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Tracker 5505 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Tracker 5505

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info