Bedienungsanleitung Navman Trackfish 6600 (Seite 78 von 83) (Englisch)

512557

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

TRACKFISH 6600 Installation and Operation Manual 79

NAVMAN

Note: For the TRACKFISH to measure fuel

consumption, the optional fuel flow kit must

be fitted.

4-1 Fuel used or remaining seem

inaccurate:

a If the engine is run while the TRACKFISH

is powered off, the TRACKFISH does not

record the amount of fuel used during

that engine run. Consequently, the Fuel

remaining value will be higher than

the actual amount of fuel remaining in the

tank.

To avoid this problem, use the Auto Power

Wiring option (see section 16-5).This

ensures that the TRACKFISH powers on

automatically whenever the boat’s ignition

is switched on.

b In rough seas, fuel may surge back and

forth through the fuel transducer, resulting in

incorrect readings. Try installing a one-way

valve between the fuel transducer and the

fuel tank.

c The Set remaining fuel value

must be reset after every refuelling

(see section 15-5).

d The fuel tank may not reﬁ ll to the same

capacity each time due to air pockets. This is

particularly noticable with underﬂ oor tanks.

e Fuel transducers wear out over time and

should be replaced after every 5000 litres

of fuel.

4-2 Flow indicates no fuel or low fuel:

a Check that the number of engines is set

to 1 (see section 15-5).

b Check that the fuel cable connectors are

securely plugged in and the collar is locked

in place. The collar must be locked in place

to give a watertight connection.

c A fuel transducer may be clogged. If so,

remove the transducer from the fuel line

and gently blow through it in the opposite

direction to the fuel ﬂ ow.

A fuel ﬁ lter between the fuel transducer and

the fuel tank must be installed as per the

fuel installation guide. Failure to do so will

void the warranty.

d Inspect the fuel cable from end to end for

damage such as cuts, breaks, trapped or

squashed sections.

B-4 Fuel consumption problems

e Check that the fuel ﬁ lter is clean.

4-3 A twin engine installation shows only

one flow rate:

a Check that the number of engines is set

to 2 (see section 15-5)

4-4 Erratic Fuel Flow readings:

a The fuel ﬂ ow transducer may have been

mounted too close to the fuel pump or may

be subject to excessive vibration. Refer to

the installation instructions supplied with the

fuel transducer.

b Check for leaks in the fuel line or in the fuel

pickup in the tank.

c The Flow ﬁ lter value is not suitable for

the engine. Check that the value is not set

to zero, then try increasing the value until

a steady ﬂ ow rate is shown (see section

15-5)

4-5 There is no reading for fuel economy:

a The boat must be travelling through the

water to generate an Economy reading.

b Check that the paddlewheel on the

transducer is spinning freely and that the

two magnets in the paddlewheel are still in

place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Trackfish 6600 Seite 78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Trackfish 6600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info