Bedienungsanleitung Navman Wind 3150 (Seite 15 von 17) (Englisch)

512551

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

WIND 3150 Installation and Operation Manual

NAVMAN

Physical

Case size 111 mm (4.4") square.

LCD display 27 mm (1.1") wide, 18 mm (0.7")

high; twisted nematic.

LCD digits 14 mm (0.55") high.

Four operator keys, laser etched.

Backlighting for display and keys, amber, four

levels and off (the key backlight does not turn off).

Operating temperature 0 to 50°C (32 to 122°F).

Power cable length 1 m (3.25 ft).

Masthead unit cable length 30 m (99 ft).

Electrical

Power supply 10.5 to 16.5 V DC, 20 mA without

backlighting, 140 mA with full backlighting and

transducer.

External beeper or light output, switched to

power negative to turn on the beepers or lights,

30 V DC and 250 mA maximum.

Wind

Wind angle, true and apparent: Range 0 to

180°, port or starboard.

Wind speed, true and apparent: Range 0 to 199

knots (0 to 102 m/s).

Maximum apparent wind speed.

Apparent wind speed alarm.

Calibration

Wind speed and wind angle can be calibrated.

Appendix A - Specifications

Interfaces

NavBus connection to other NAVMAN

instruments.

NMEA 0183 outputs: MWV, VPW; inputs RMC,

VHW, VTG.

Standards compliance

EMC compliance

USA (FCC): Part 15 Class B.

Europe (CE): EN50081-1, EN50082-1

New Zealand and Australia (C Tick):

AS-NZS 3548.

Environment: IP66 from front when correctly

mounted.

Power/data cable wires

Wire Signal

Red Power positive, 12 V DC, 140 mA

maximum

Black Power negative, NMEA common

Green External beeper or light out, switched to

power negative, 30 V DC and 250 mA

max.

Orange NavBus +

Blue NavBus -

White NMEA out

Yellow NMEA in

Appendix B - Troubleshooting

This troubleshooting guide assumes that you have

read and understood this manual.

It is possible in many cases to solve difficulties

without having to send the unit back to the

manufacturer for repair. Please follow this

troubleshooting section before contacting the

nearest NAVMAN dealer.

There are no user serviceable parts. Specialized

methods and testing equipment are required to

ensure that the unit is reassembled correctly and is

waterproof. Repairs to the unit must only be carried

out by a service centre approved by Navman NZ

Limited. Users who service the unit themselves will

void the warranty.

More information can be found on our website:

www.navman.com

1 Unit will not turn on:

a Fuse blown or circuit breaker tripped.

b Battery voltage is outside the range 10.5 to

16.5 V DC.

c Power/data cable damaged.

2 Wind speed or angle reading wrong or erratic:

a Masthead unit is damaged, fouled or

corroded.

b Wind speed calibration is incorrect (see

section 8-2).

c Wind angle calibration is incorrect (see

section 8-1).

d Masthead unit cable unplugged or

damaged.

e Interference from electrical noise. Review

installation.

3 The word SIM flashes on the LCD display or

the values displayed are unexpected:

a Unit is in simulate mode (see section 2-5).

4 The display fogs:

a Moist air has entered the breathing tube at

the rear of the unit. Air the boat or run unit

with backlight fully on.

b Water has entered the breathing tube.

Return unit for service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Wind 3150 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Wind 3150

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info